Software Guide

ManualsBrandsToro ManualsRiding ProductsGroundsmaster 5910 Rotary Mower

FormNo.3441-598RevA

Groundsmaster

5900or5910RotaryMower

ModelNo.31698—SerialNo.407050000andUp

ModelNo.31699—SerialNo.407050000andUp

SoftwareGuide

ReadthisinformationcarefullytolearnhowtooperatetheInfoCentercontrolonyourproduct.Youare

responsibleforoperatingtheproductproperlyandsafely.

Visitwww.Toro.comforproductsafetyandoperationtrainingmaterials,accessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Introduction

TheSoftwareGuidefortheGroundsmaster

5900or

5910rotarymowerprovidesinformationforusingthe

systeminformationandcontrolthesystemfunctions.

Contents

Introduction...............................................................1

ProductOverview.....................................................1

Controls.............................................................1

Operation..................................................................2

InfoCenterControl..............................................2

AccessingtheProtectedMenus..........................5

ChangingtheInfoCenterPIN..............................7

SettingtheServiceDueTimer............................8

ChangingtheInfoCenterDisplay

Brightness/Contrast........................................9

SettingtheCruise-ControlSpeed.......................9

InfoCenterAdvisories........................................11

ProductOverview

Controls

InfoCenterStartupScreen

Whenyoustartthemachine,thestartupscreen

appears,displayingthecorrespondingiconsthatapply

(i.e.,theparkingbrakeisapplied,thePTOisintheON

position,andthecruisecontrolisintheONposition).

Note:Thefollowinggureisanexamplescreen;this

screenismeanttoshowallthepotentialiconsthat

couldappearonthescreenwhileoperating.

Refertothefollowinggraphicforalloftheicon

meanings(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3441-598*

Summary of content (16 pages)

PAGE 1
Form No. 3441-598 Rev A Groundsmaster® 5900 or 5910 Rotary Mower Model No. 31698—Serial No. 407050000 and Up Model No. 31699—Serial No. 407050000 and Up Software Guide Read this information carefully to learn how to operate the InfoCenter control on your product. You are responsible for operating the product properly and safely. Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
PAGE 2
g033320 Figure 1 1. PTO indicator 6. Engine speed 2. Glow-plug indicator 7. Cruise-control-set indicator 8. Engine-hours indicator 3. Parking-brake indicator 4. Diesel-particulate filter (DPF) maintenance indicator 5. Fan-reverse indicator 9. H/L (High/Low) transmission-range indicator g033145 Figure 2 Operation InfoCenter Control 1. Screen 1—top, left screen 6. Audible alarm 2. Button 1 3. Screen 2—top, right screen 4. Button 2 5. Button 3 7. Button 4 8. Fault screen 9. Button 5 10.
PAGE 3
Note: In the following example, the hydraulic-fluid-cooling fans are running at 25% speed in the forward direction. • Engine-coolant-temperature and fan indicator—top, left screen (Figure 5) Note: In example Figure 5, the engine-coolant fans are running at 50% speed in the reverse direction. This display (Figure 1) indicates fan speed and direction. The fan speed is controlled by the hydraulic-fluid temperature or the engine-coolant temperature, and automatically reverses as needed.
PAGE 4
Hydraulic-Fluid-Temperature Indicator and Cooling-Fan-Status Indicator If a fault appears on the screen, press any key to view the active fault advisory (Figure 2). Note: Contact your supervisor or mechanic to relay the fault advisory and determine the course of action. This display indicates the hydraulic-fluid temperature and the status of the cooling fan (Figure 5). Press the arrow keys to navigate the fault screen. Press any key to reveal the information keys on the screen.
PAGE 5
Accessing the Protected Menus • The PTO is requested and qualified • Any deck is below the limit, but not floating Machine sends a request to the InfoCenter Note: The factory default PIN code for you machine is either 0000 or 1234. If you changed the PIN code and forgot the code, contact your authorized Toro distributor for assistance.
PAGE 6
g214883 g214879 Figure 8 If the menus are protected, the ENTER PIN screen displays. 3. Press buttons 1 through 4 to enter your PIN code (Figure 9). g214882 Figure 10 Note: When you shutoff the engine and then move the ignition switch to the RUN position, PIN code protection is applied to the MAIN MENU. g214881 Figure 9 4. When you complete entering the PIN, press button 5 (Figure 10). The InfoCenter displays the MAIN MENU.
PAGE 7
Changing the InfoCenter PIN 1. From the startup screen, press and hold button 5 until the Main Menu appears (Figure 11). g033169 Figure 13 5. g033167 Press button 2 until you reach PIN Change on the PIN Settings screen and press button 4 to select PIN Change (Figure 14). Figure 11 2. Press button 2 until you reach Settings on the Main Menu screen and press button 4 to select Settings (Figure 11). 3. From the Settings screen, press button 4 to select Display (Figure 12). g033170 Figure 14 6.
PAGE 8
g033174 g033172 Figure 17 Figure 15 1. Digit 1 2. Digit 2 4. Digit 4 1. Digit 1 4. Digit 4 5. Enter PIN 2. Digit 2 5. Enter PIN 3. Digit 3 3. Digit 3 7. Enter your new PIN using buttons 1 to 4 and press button 5 when you complete your new PIN (Figure 16). Setting the Service Due Timer 1. After you complete entering the PIN number for the protected menus, press button 5. 2. Scroll up or down to SERVICE in the main menu (Figure 18). g033173 Figure 16 1. Digit 1 4. Digit 4 2. Digit 2 5.
PAGE 9
5. In the HOURS menu select the middle button to select RESET HOURS. 1. Move the cruise-control switch to the ON position. 6. Scroll up or down to select the correct hours. 2. 7. Press the side arrow button. 8. Exit the menu by selecting the EXIT (door) button (Figure 18 orFigure 19). When the cruise-control icon appears on the display screen, press button 1 to 4 to access the pop-up-menu bar. 3. Press button 3 to access the Cruise Control screen (Figure 20).
PAGE 10
g033180 Figure 21 1. Decrease cruise control speed 3. Exit 2.
PAGE 11
InfoCenter Advisories Operator advisories automatically display on the InfoCenter screen when a machine function requires additional action. For example, if you attempt to start the engine while pressing the traction pedal, an advisory displays, indicating that the traction pedal must be in the NEUTRAL position. For each advisory that occurs, there is a condition (e.g.
PAGE 12
PTO Denied 110 Hydraulic fluid too cold To engage PTO, let hydraulic fluid warm up Cruise Control Denied 202 Too slow to capture cruise control Increase ground speed Deck Lower Denied 302 Can’t lower in transport To lower deck, return traction pedal to NEUTRAL Deck Lower Denied 303 Out of seat To lower deck, operator must be seated Deck Lower Denied 304 Service required To lower deck, requires service Deck Not Floating (on engine start) 402 Advise operator to press down switches To fl
PAGE 13
Engine Advisory 1210 Engine derate due to high temperature Let engine cool Engine Advisory 1211 Engine speed restricted: hydraulic fluid too cold Hydraulic fluid is less than 4°C (40°F), so derate the engine speed to 1,650 rpm Fuel Level 1302 Fuel level is low Add fuel TP Not Calibrated 1402 Traction pedal is out of calibration Calibrate the traction pedal Teach 1500 Entered teach mode Entered traction pedal teach—please wait Teach 1502 Traction pedal is out of NEUTRAL Return traction
PAGE 14
Deck Raise Denied 1605 Service required Contract your Toro distributor Deck Raise Denied 1606 All decks not raising together Increase the engine speed to 2,000 rpm, and the decks will raise one at a time when all 3 switches are held down simultaneously 14
PAGE 15
Notes:
PAGE 16