Form No. 3409-974 Rev B Groundsmaster® 360 2-Wheel Drive, 4-Wheel Drive, or 4-Wheel Drive with Cab Multi-Purpose Machine Model No. 31200—Serial No. 400000000 and Up Model No. 31202—Serial No. 400000000 and Up Model No. 31203—Serial No. 400000000 and Up Register at www.Toro.com.
WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. g014165 Figure 1 Genuine Toro spark arresters are approved by the USDA Forestry Service. 1.
Contents Engine Safety ................................................... 48 Servicing the Air Cleaner .................................. 48 Servicing the Engine Oil.................................... 49 Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter .............................. 50 Fuel System Maintenance ................................... 51 Servicing the Water Separator .......................... 51 Servicing the Engine Fuel Filter ........................
Safety • Keep clear of any discharge opening. Keep This machine has been designed in accordance with EN ISO 5395:2013 and ANSI B71.4-2012. • Keep children out of the operating area. Never bystanders and pets a safe distance away from the machine. allow children to operate the machine. General Safety • Stop the machine and shut off the engine before This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury.
decal117-4766 117-4766 1. Cutting/dismemberment hazard; fan—stay away from moving parts; keep all guards and shields in place. decal117-3270 117-3270 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, hand; entanglement hazard, belt—stay away from moving parts; keep all guards and shields in place. decal98-4387 98-4387 1. Warning—wear hearing protection. decal120-6604 decal117-3272 120-6604 117-3272 1. Thrown object hazard—keep bystanders away from the machine. 2.
decal117-2718 117-2718 decal107-2908 107-2908 1. Thrown object hazard—keep bystanders a safe distance away from the machine. 2. Thrown object hazard—do not operate the mower with the deflector up or removed; keep the deflector in place. 3. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. decal106-9206 106-9206 1. Explosion hazard 6.
decal117-3273 117-3273 1. Warning—read the Operator's Manual. 6. Thrown object hazard—keep bystanders a safe distance away from the machine. 2. Warning—do not operate this machine unless you are trained. 7. Warning—engage the parking brake, shut off the engine, and remove the key from the key switch before leaving the machine. 3. Warning—wear the seat belt when seated in the operator's 8. Tipping hazard—lower the cutting unit when driving down position.
decal121-8378 121-8378 Model with Cab Only 5. 6. 7. 8. External air Internal air Air conditioner—off Air conditioner—on 0000 000000 0000 000000 0000 000000 000000 000000 000000 Fan—off Fan—on full Cold air Hot air 000000 1. 2. 3. 4. 0 0 00000 00000 00000 00000 00000 00000 00000 00000 00000 00 0 00 0 00 0 0 000 00 0 0 decal125-9248 125–9248 Model with Cab Only 5. Fast 6. Slow 1. Raise/Lower decks 2. Engine—stop 3. Engine—run 7. 2-wheel steering 4. Engine—start 8.
decal132-3600 132-3600 Model with Cab Only 1. Read the Operator's Manual for more information on fuses. 2. Headlight (25 A) 5. Working light (20 A) 3. Condenser fan and A/C clutch (30 A) 7. Cab light (15 A) 4. Fan (25 A) 8. Windshield wipers (15 A) 6. Auxiliary power (15 A) decal130-0594 130-0594 Model with Cab Only 1. Warning—read the Operator’s Manual; when sitting in the cab, always wear a seat belt; wear hearing protection. decal125-9688 125-9688 Model with Cab Only 1.
decal120-0250 120-0250 decal132-6553 132-6553 Model with Cab Only 1. Slow-moving vehicle 1. Height of cut decal131-1946 131–1946 1. Read the Operator’s Manual for more information on servicing the machine.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 5 Use Qty. PTO driveshaft Bolt (5/16 x 1-3/4 inches) Locknut (5/16 inch) Roll pin (3/16 x 1-1/2 inches) Retainer pin Grease fitting Washer head screw (5/16 x 7/8 inch) 1 4 4 2 2 2 2 No parts required – Adjust the roll bar. No parts required – Check the tire pressure. No parts required – Check the levels of the hydraulic fluid, engine oil, and coolant.
D. Torque the locknuts to 20 to 25 N-m (175 to 225 in-lb). 7. Lubricate the grease fittings on the PTO driveshaft. 8. After you connect the other end of the driveshaft to the attachment gearbox shaft, connect the wire-harness connector to the PTO solenoid-valve-coil connector (Figure 3). 2 G018339 1 g018339 Figure 3 Using the Optional Mower-Deck-Mounting Hardware 1. Wire-harness connector 3. Position the PTO driveshaft under the front of the machine.
Do not wear the seat belt when the roll bar is folded down. 3. Check the cooling system before starting the engine; refer to Checking the Cooling System (page 55). g014166 Figure 5 1. Roll bar 3. Hairpin cotter 2. Pin 4 Checking the Tire Pressure No Parts Required Procedure The tires are overinflated for shipping. Therefore, release some of the air to reduce the pressure. Check the tire pressure; refer to Checking the Tire Pressure (page 54).
Tilt-Steering Pedal Product Overview To tilt the steering wheel toward you, press the foot pedal down and pull the steering tower toward you to the most comfortable position and then release the pedal (Figure 6). Controls Become familiar with all the controls before you start the engine and operate the machine. Engine-Speed Switch Traction Pedal The engine-speed switch (Figure 7) has 2 modes to change the engine speed.
Power Point Cab Controls The power point provides a 12 V power supply for electronic devices (Figure 7). Model with Cab Only Important: If the mower deck shuts down and the InfoCenter temperature-warning icon is on, push the PTO knob down; drive to a safe, flat area; move the throttle lever to the SLOW position; allow the traction pedal to move to the NEUTRAL position; and engage the parking brake. Allow the engine to idle for several minutes while it cools to a safe level.
Using the InfoCenter LCD Display The InfoCenter LCD display shows information about your machine, such as the operating status, various diagnostics, and other information about the machine (Figure 11). There is a splash screen and main information screen of the InfoCenter. You can switch between the splash screen and main information screen at any time by pressing any of the InfoCenter buttons and then selecting the appropriate directional arrow. 1 TORO g196911 Figure 10 1.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.) Indicates when scheduled service should be performed Engine rpm/status—indicates the engine rpm InfoCenter Hour meter Bad or failed Bulb Info icon Output of TEC controller or control wire in harness Fast Switch Slow Operator must release switch Stationary regeneration required Operator should change to indicated state Symbols are often combined to form sentences.
Faults Service Diagnostics Settings About The Faults menu contains a list of the recent machine faults. Refer to the Service Manual or your Authorized Toro Distributor for more information on the Faults menu and the information contained there. Settings The Service menu contains information on the machine such as hours of use counters and other similar numbers. The Diagnostics menu displays the state of each machine switch, sensor and control output.
1. From the MAIN MENU, use the center button to scroll down to the SETTINGS MENU and press the right button (Figure 12). “PIN” displays in the upper right corner of the screen. Note: Rotate the key switch to the OFF position and then to the ON position locks the protected menu. You have the ability to view and change the settings in the Protected Menu. Once you access the Protected Menu, scroll down to Protect Settings option. Use the right button to change the setting.
Specifications Note: Specifications and design are subject to change without notice.
Operation Weight of the Machine with Mower Decks 4-Wheel Drive Machine with ROPS Machine with Cab 2-Wheel Drive Machine with ROPS No mower deck 1,152 kg (2,540 lb) 1,435 kg (3,163 lb) 1,130 kg (2,492 lb) 72 inch side discharge mower deck 1,363 kg (3,004 lb) 1,645 kg (3,627 lb) 1,341 kg (2,956 lb) 72 inch base mower deck 1,341 kg (2,956 lb) 1,623 kg (3,579 lb) 1,319 kg (2,908 lb) 62 inch base mower deck 1,324 kg (2,918 lb) 1,606 kg (3,541 lb) 1,302 kg (2,870 lb) 100 inch rear discharge mo
Adding Fuel Biodiesel fuel specification: ASTM D6751 or EN14214 Fuel Specification Blended fuel specification: ASTM D975, EN590, or JIS K2204 Important: Use only ultra-low sulphur diesel fuel. Fuel with higher rates of sulfur degrades the diesel oxidation catalyst (DOC), which causes operational problems and shortens the service life of engine components. Failure to observe the following cautions may damage the engine. • Never use kerosene or gasoline instead of diesel fuel.
Think Safety First 4. Add fuel to the fuel tank until the level is even with the bottom of the filler neck. Do not overfill the fuel tank. Please read all safety instructions and symbols in the safety section. Knowing this information could help you or bystanders avoid injury. 5. Install the fuel-tank cap and secure. Wipe up any spilled fuel.
NEUTRAL position with the parking brake engaged. If you rise from the seat when the PTO is engaged, there is a 1-second delay and then the engine shuts off. Positioning the Standard Seat Testing the Safety-Interlock System Changing the Seat Position The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. Service Interval: Before each use or daily Test the safety interlock system before you use the machine each time.
g004489 Figure 18 1. Seat-suspension knob 2. Operator-weight setting g014174 Figure 19 Changing the Back Position 1. Seat latch You can adjust the back of the seat to provide a comfortable ride. Position the back of the seat where it is most comfortable. 2. To lower the seat, pull up the seat-latch-release bar and lower the seat into the locked position. To adjust the back of the seat, turn the knob, located under the right-side armrest, in either direction to provide the best comfort (Figure 17).
During Operation During Operation Safety General Safety • • The owner/operator can prevent and is responsible • • • • • • • • • • • • • • • • for accidents that may cause personal injury or property damage. Wear appropriate clothing, including eye protection; slip-resistant, substantial foot protection; and hearing protection. Tie back long hair and do not wear jewelry. Do not operate the machine while ill, tired, or under the influence of alcohol or drugs.
use common sense and good judgment when performing this survey. WARNING To avoid injury or death from rollover, keep the roll bar in the raised locked position and use the seat belt. • Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. Operating the machine on any slope requires extra caution. Ensure that the seat plate is secured with the seat latch. • Operate the machine at a lower speed when you are on a slope.
Important: Use starting cycles of no 3. Install the 2 pins and secure them with the hairpin cotters (Figure 21). more than 15 seconds per minute to avoid overheating the starter motor. Important: Ensure that the seat is secured with the seat latch. Note: Additional starting cycles may be required when starting the engine for the first time after the fuel system has been completely drained. 4. To raise the roll bar, remove the hairpin cotter pins and remove the 2 pins (Figure 21). 5.
Stopping the Machine switch light is continuously off, the machine is in the 4-wheel-steering mode. To stop the machine, release the traction pedal to the NEUTRAL position. Note: If you turn the steering wheel too briskly, steering misalignment may occur. Engage the parking brake whenever you leave the machine. Remove the key from the key switch.
g026087 g026087 Figure 25 1. PTO switch Disengaging the PTO To disengage the PTO, push the switch to the position. g014263 Figure 26 OFF 1. Height-of-cut pin Adjusting the Height of Cut 4. Adjust the anti-scalp rollers and skids as required. You can adjust the height of cut from 2.5 to 15.8 cm (1 to 6 inches) in 6 mm (1/4 inch) increments by relocating the height-of-cut pin into different hole locations. Cutting Grass with the Machine 1.
Diesel Particulate Filter Regeneration Important: Minimize the amount of time that you idle the engine or operate the engine at low-engine speed to help reduce the accumulation of soot in the soot filter. The diesel particulate filter (DPF) is part of the exhaust system. The diesel-oxidation catalyst of the DPF reduces harmful gasses and the soot filter removes soot from the engine exhaust.
DPF Ash Accumulation • When enough ash accumulates, the engine • The lighter ash is discharged through the exhaust system; the heavier ash collects in the soot filter. • Ash is a residue of the regeneration process. Over • time, the diesel particulate filter accumulates ash that does not discharge with the engine exhaust. • • The computer for the engine calculates the amount of ash accumulated in the DPF.
Types of Diesel Particulate Filter Regeneration Types of diesel particulate filter regeneration that are performed while the machine is operating: Type of Regeneration Conditions for DPF regeneration DPF description of operation Passive Occurs during normal operation of the machine at high-engine speed or high-engine load The InfoCenter does not display an icon indicating passive regeneration.
Types of diesel particulate filter regeneration that require you to park the machine: (cont'd.) Type of Regeneration Conditions for DPF regeneration DPF description of operation Recovery Occurs as a result of ignoring parked regeneration requests and continuing operation, adding more soot when the DPF is already in need of a parked regeneration When the recovery-regeneration icon is displayed in the InfoCenter, a recovery regeneration is requested.
Reset Regeneration Parked Regeneration g214713 g214711 Figure 34 Assist/reset-regeneration icon Figure 35 Parked-regeneration request icon • The assist/reset-regeneration icon displays in the • The parked-regeneration requested icon displays InfoCenter (Figure 34). • • The computer takes control of the intake throttle and changes the fuel injection operation to increase the temperature of the engine exhaust. in the InfoCenter (Figure 35).
6. Engage the parking brake. 7. Set the throttle to the low IDLE position. Performing a Parked Regeneration Note: For instructions on unlocking protected menus, refer to Accessing Protected Menus (page 18). 1. Access the protected menu and unlock the protected settings submenu (Figure 37); refer to Accessing Protected Menus (page 18). g212138 Figure 39 4. When the “Initiate DPF Regen. Are you sure?” message displays, press the center button (Figure 40). g028523 Figure 37 2.
g211986 g212405 Figure 41 Figure 43 6. Move the throttle control to LOW IDLE and press the center button (Figure 42). B. The “Waiting on (Figure 44). ” message displays g212372 g212406 Figure 42 Figure 44 7. The following messages display as the parked regeneration process begins: C. The computer determines whether the regeneration runs. One of the following messages displays in the InfoCenter: A. The “Initiating DPF Regen.” message displays (Figure 43).
The engine is cold—wait. The engine is warm—wait. The engine hot—regeneration in progress (percent complete). 9. The parked regeneration is complete when the “Regen Complete” message displays in the InfoCenter. Press the left button to exit to the home screen (Figure 47). g213424 Figure 45 • If the regeneration process is not allowed by the engine computer, the “DPF Regen Not Allowed” message displays in the InfoCenter (Figure 46).
• Perform a recovery-regeneration whenever raise the cutting height higher than usual and cut the grass at this setting. Then cut the grass again using the lower, normal setting. there is a loss of engine power and a parked regeneration cannot effectively clean the DPF of soot. • A recovery regeneration requires up to 4 hours Keeping the Mower Clean to complete. Clean clippings and dirt from the underside of the mower after each use.
After Operation 5. Disengage the parking brake before pushing the machine. After Operation Safety Changing to Machine Operation • Clean grass and debris from the cutting units, 1. Rotate each bypass valve clockwise 1 turn and hand tighten them (Figure 49). mufflers, and engine compartment to help prevent fires. Clean up oil or fuel spills. Note: Do not overtighten the bypass valves. • If the cutting units are in the transport position, use 2.
Locating the Tie-Down Points There are tie downs located at the front and rear sides of the machine (Figure 50). Note: Use properly-rated DOT-approved straps in 4 corners to tie down the machine. • 2 on the front of the operator's platform • Rear tire g014264 Figure 50 1.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • Check the tension of the alternator belt. • Torque the wheel lug nuts. After the first 200 hours • Change the hydraulic fluid and filter. Before each use or daily • • • • • Test the safety system. Check the air-cleaner indicator.
Daily Maintenance Checklist Duplicate this page for routine use. For the week of: Maintenance Check Item Monday Tuesday Wednesday Thursday Friday Saturday Check the safety-interlock operation. Check the brake operation. Check the engine-oil level. Check the cooling-system-fluid level. Drain the water/fuel separator. Check the air filter, dust cup, and burp valve. Check for unusual engine noises.2 Check the radiator and screen for debris Check for unusual operating noises.
Notation for Areas of Concern Inspection performed by: Item Date Information CAUTION If you leave the key in the key switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the key switch before you do any maintenance. decal131-1946 Figure 51 Service Interval Chart Pre-Maintenance Procedures – Shut off the engine and remove the key. – Wait for all moving parts to stop. – Allow machine components to cool before performing maintenance.
Preparing the Machine for Maintenance 1. Ensure that the PTO is disengaged. 2. Park the machine on a level surface. 3. Engage the parking brake. 4. Lower the mower deck(s) if necessary. 5. Shut off the engine and wait for all moving parts to stop. 6. Turn the key to the STOP position and remove it. 7. Allow machine components to cool before performing maintenance. Using the Hood-Prop Rod 1. Release the hood latches. 2. Lift up the hood until you can position the prop rod behind the frame tube (Figure 52).
Lubrication Greasing the Bearings and Bushings Service Interval: Every 50 hours Grease the bearing and bushing grease fittings more frequently in extremely dusty and dirty conditions. The machine has grease fittings that you must lubricate regularly with No. 2 lithium grease. Lubricate the grease fittings immediately after every washing, regardless of interval specified. 1. Wipe the grease fittings clean so that foreign matter cannot be forced into the bearing or bushing (Figure 53). 2.
Note: To access the grease fittings for the rear-steering linkage, remove the storage compartment. Note: Raise the machine off the floor to allow better grease migration through both the upper and lower king-pin bushings. You should see grease purging out of both the top and the bottom of the axle casting/bushing assembly areas of all 4 kingpin assemblies (Figure 54). G026734 g026734 Figure 54 Note: The bearing life can be negatively affected by improper washing procedures.
Engine Maintenance Engine Safety • Shut off the engine before checking the oil or adding oil to the crankcase. • Do not change the governor speed or overspeed the engine. Servicing the Air Cleaner Service Interval: Before each use or daily—Check the air-cleaner indicator. Every 400 hours—Service the air cleaner (earlier if the air cleaner indicator shows red, and more frequently in extremely dirty or dusty conditions). Check the air-cleaner body for damage, which could cause an air leak.
checking. If the oil level is at or below the Add mark on the dipstick, add oil to bring the oil level to the Full mark. Do not overfill the engine with oil. Important: Keep the engine oil level between the upper and lower limits on the dipstick; the engine may fail if you run it with too much or too little oil. 1. Park the machine on a level surface, engage the parking brake, shut off the engine, remove the key from the key switch. g011505 2.
3720 FMI 16in the InfoCenter (Figure 61) display in the InfoCenter, clean the soot filter using the steps that follow: SPN g214715 g213864 g213863 Figure 61 Figure 59 1. Refer to the Engine section in the Service Manual for information on disassembling and assembling the diesel-oxidation catalyst and the soot filter of the DPF. 4. Add oil to the crankcase; refer to Checking the Engine-Oil Level (page 49). 2.
Fuel System Maintenance Note: Refer to Fuel Specification (page 22) for the proper fuel recommendations. DANGER Under certain conditions, diesel fuel and fuel vapors are highly flammable and explosive. A fire or explosion from fuel can burn you and others and can cause property damage. • Use a funnel and fill the fuel tank outdoors, in an open area, when the engine is off and is cold. Wipe up any fuel that spills. • Do not fill the fuel tank completely full.
Servicing the Engine Fuel Filter Electrical System Maintenance Service Interval: Every 400 hours Important: Whenever working with the electrical system, always disconnect the battery cables, negative (-) cable first, to prevent possible wiring damage from short-outs. 1. Clean the area around the filter head (Figure 63). Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last.
Servicing the Battery Service Interval: Every 50 hours Keep the top of the battery clean. If you store the machine in a location where temperatures are extremely high, the battery will run down more rapidly than if the machine is stored in a location where temperatures are cool. Keep the top of the battery clean by washing it periodically with a brush dipped in ammonia or baking-soda solution. Flush the top surface with water after cleaning it. Do not remove the fill caps while cleaning the battery.
Drive System Maintenance deterioration of the charge in the battery. To prevent the battery from freezing, make sure that it is fully charged. The specific gravity of a fully charged battery is 1.265 to 1.299. Checking the Tire Pressure Service Interval: Every 50 hours Maintain the air pressure in the front and rear tires. The correct air pressure is 172 kPa (25 psi) in the rear tires and 103 kPa (15 psi) in the front tires.
Cooling System Maintenance synchronization of wheel alignment should occur. Important: Doing this procedure on turf can result in turf directly under each of the turning tires. Cooling System Safety • Swallowing engine coolant can cause poisoning; keep out of reach from children and pets. • Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns. – Always allow the engine to cool at least 15 minutes before removing the radiator cap.
compressed air (do not use water). Repeat this step from the front of the radiator, again from the fan side. 3. Install the expansion-tank cap. 4. After you have thoroughly cleaned the radiator, remove any debris from the channel at the radiator base and around the frame. 5. Clean the engine compartment and the brake linkage. 6. Close the clean-out cover and secure the flange nut. 7. Close the hood. g014268 Figure 69 1.
Brake Maintenance Adjusting the Parking Brake Adjusting the Service Brakes If the parking brake fails to engage, an adjustment to the brake pawl is required. 1. Loosen the 2 screws securing the parking-brake pawl to the frame (Figure 72). Adjust the service brakes when there is more than 25 mm (1 inch) of free travel of the brake pedal, or when the brakes do not work effectively. Free travel is the distance that the brake pedal moves before you feel braking resistance.
Belt Maintenance Controls System Maintenance Checking the Alternator Belt Adjusting the Traction Drive for Neutral Service Interval: After the first 10 hours Every 100 hours Note: If the machine has recently had the hydraulic fluid changed or the traction motors or hoses replaced, work out any air trapped in the system prior to performing this procedure. To do this, operate the machine in forward and reverse for a few minutes and then replenish the oil as required.
Adjusting the Maximum Ground Speed 1. Park the machine on a level surface, disengage the PTO, release the traction pedal to the NEUTRAL position, and engage the parking brake. 2. Move the throttle lever to the SLOW position, shut off the engine, remove the key from the key switch, and wait for all moving parts to stop before leaving the operating position. 3. Loosen the jam nut on the stop bolt for the traction pedal (Figure 75). g026002 Figure 74 1.
Hydraulic System Maintenance speed, adjust the stop bolt in; to decrease the reverse speed, adjust the stop bolt out. Hydraulic System Safety • Ensure that all hydraulic-fluid hoses and lines are in good condition and all hydraulic connections and fittings are tight before applying pressure to the hydraulic system. • Keep your body and hands away from pinhole leaks or nozzles that eject high-pressure hydraulic fluid. • Use cardboard or paper to find hydraulic leaks.
3. Raise the deck to extend the lift cylinders, shut off the engine, and remove the key from the key switch. 4. Remove the hydraulic-filler cap (Figure 76) from the filler neck. 5. Remove the dipstick and wipe it with a clean rag (Figure 76). 6. Screw the dipstick all the way into the filler neck; then remove it, and check the level of the fluid (Figure 76). If the level is not within the notched area of the dipstick, add enough high-quality hydraulic fluid to raise the level to within the notched area.
Cab Maintenance 1 2 Filling the Washer-Fluid Bottle 1. Perform the pre-maintenance procedure; refer to Preparing the Machine for Maintenance (page 45). 2. Open the hood and locate the washer-fluid bottle (Figure 78). 3 g028378 g028378 Figure 79 1. Filter 2. Grate 3. Screw 1 g028438 Figure 78 Washer-Fluid Bottle with Washer-Fluid Symbol 3. Fill the bottle with washer fluid as needed. 4. Close the hood.
Cleaning the Air-Conditioning Coil 5. Clean the screen, air-conditioning duct, fans, and fan panel using low-pressure air no greater than 276 kPa (40 psi). Important: Do not use water to clean the condenser because moisture on the components attracts dirt and dust, which make the components more difficult to clean. Service Interval: Every 50 hours Clean the air-conditioning coil more frequently in extremely dusty or dirty conditions. 1.
Cleaning Storage Cleaning the Cab Preparing the Engine 1. Drain the engine oil from the oil pan and install the drain plug. Important: Use care around the cab seals and lights (Figure 83). If you are using a pressure washer, keep the washer wand at least 0.6 m (2 ft) away from the machine. Do not use the pressure washer directly on the cab seals and lights or under the rear overhang. 2. Change the engine oil and filter; refer to Changing the Engine Oil and Filter (page 49). 3.
C. Coat the cable terminals and battery posts with Grafo 112X skin-over grease (Toro Part No. 505-47) or petroleum jelly to prevent corrosion. D. Slowly charge the battery for 24 hours every 60 days to prevent lead sulfation of the battery.
Notes:
Notes:
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
