FORM NO. 3313-456 OPERATOR'S MODEL NO. 30784 MANUAL CRUISE CONTROL FOR GROUNDS MASTER 300 SERIES W/POWER STEERING Since this operator's manual covers only a minimal amount of information necessary to maintain and operate your machine, we suggest that you keep this material with your traction unit operator’s manual so that both may be referred to for instructions concerning safe operation and proper maintenance procedures.
Firefight 7. Push down 2. Switch bey flush with pedal 3. Rectangle TOWER COVER MODIFICATION 1. Two modifications are required. Measure and mark and back from the right front corner of tower cover top {Fig. 4. Figure 4 2. Cut sheet metal 9/16" in at each mark. Bend metal between marks downward {Fig. 4). Remove all sharp edges. 3. For brake pedal spring clearance, measure and mark up from lower left corner of the tower cover {Fig. 4).
INSTALL TRACTION PEDAL AND CLUTCH ASSEMBLY 3. Assemble external tooth lock washers onto mounting screws and secure cover to box {Fig. 7). 1. Remove nut securing traction pedal shaft to bracket and remove and discard bracket {Fig. 9). 1. Wut 2. Fraction pedal shalt 3. Bracket 2. Remove and discard cotter pins from traction pedal shaft {Fig. 10} Figure 7. Aunt screws and external tooth lock washers 4.
. Remove foot rest side plate. Matching the radius in lower front corner, measure in on plate, scribe and trim area off plate {Fig. 12). Set plate aside for further use. FOOT REST SIDE PLATE CUY OFF 2N, {38 mm) Figure 12 5. Use original bracket mounting cap screws and instant new bracket (Fig. 13} 1. Bracket Note: Machines equipped with a Trifle 88 cutting unit will need modification of the bracket and coil assembly and addition of a hose bracket {included in kit). Refer to Trifle 88 Modifications, page 6.
9. Assemble collar, flange bushing, clutch plate, spring and another flange bushing onto the shaft at right side of traction pedal (Fig. 17} Figure 17 Costar Range bushings (2 Clutch platy . Spring At Note: Be sure socket head screw and jam nut are installed in clutch plate. 10. Position pedal assembly onto machine. Insert pump control shaft end into pedal. Secure with slotted nut and cotter pin {Fig. 18). 1. Pump control shaft 2. Totted aut and cotter pin 11.
BRACKET~, o w32 IN (2 2mm CAP SCREW, SHERLOCK . AND NUT (2} e FLANGE Easing BUSHINGS COLLAR AND SEY SCREW COPPERFIELD CONE/ fi e / COMPRESSION /7 SPRING i SOCKET HEAD SCREW CLUTCH | AND NUT Plat Laos Figure 21 Note: Clutch plate must move freely on boss and be adjustable, so it can clear traction pedal bracket fever. If adjustment isn't possible, file excess boss amendment away. TRIFLE 88 MODIFICATIONS 1.
4. Route harness under control panel. Insert red harness wire into tab connector (Fig. 28} until wire ends butts against stop in connector {Fig. 28). Fichte 25 7. Connect 2. Harness “giver 2o 2. Remove harness slack. Secure harness to front 1. Red harness wire frame with cable tie and insert coil wire lead into 2. Tab connector the harness connector {Fig. 26). : 5. Hold red wire against tab connector stop and place black wire from ignition switch to hour meter into slot in connector {Fig. 29).
7. Snap tab over top of connector {Fig. 31). 7. Snap over top of connector 8. Loop excess harness under control panel. Install instrument panel cover and foot rest side plate (Fig. 32} 1. Yogurt swatch 2. Actuating button 3. indicator tamp 3. The plate is now against coil. Rotate heft assembly on outside of coil so inner portion of shaft contacts forward end of slotted hole in clutch plate {Fig. 34). This acts as a reverse lockout when coil is engaged.
8. Turn cruise control and ignition switch to OFF. Manually actuate traction pedal to forward and reverse operating positions. Pedal should operate freely and clutch plate should clear the end of the shaft assembly in reverse pedal position {Fig. 34). if plate doesn't clear end of the shaft assembly, adjust the clutch plate further away from the coil; proceed to step 6. If plate clears the end of the shaft assembly, proceed to step 7 6.
Fhe Toto Promise A ON. The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The Hollowing time periods from the date of purchase apply. Commercial Products YEAR LIMITED WARRANTY 1 Year The costs of parts and labor are included, hut the customer pas the transportation costs on walk rotary mowers with netting unit widths of Jess than 25" It you feel your TOR product is defective and wish 10 retry on The Toto Promise, the following procedure is recommended: 1.
