Form No. 3386-715 Rev A 100in CE Mower Cover Kit Groundsmaster® 7210 Traction Unit or Groundsmaster® 360 Multi-Purpose Machine Model No. 30687 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped.
Procedure Description Shield support (Groundsmaster 7210) Shield support (Groundsmaster 360) Hex-head screw (5/16 x 4 inches) Washer Flange nut Driveshaft shield Shoulder bolt Washer (0.469 x 0.922 inch) Push nut 11 12 Use Qty. 1 1 1 1 1 1 1 1 1 Mount the shield support. Mount the driveshaft shield. Media and Additional Parts Description Use Qty. Installation instructions 1 Reference the instructions for installing the kit. Parts catalog 1 Use the catalog to reference part numbers.
1 2 3 3 Mounting the Front Shields Parts needed for this procedure: 2 Front shield Procedure Install the left and right front shields onto the machine (Figure 3). g026870 Figure 2 1. Nut (2) Note: Remove the nuts at the front of the left and right spindles and use them to install the front shields. 3. Pulley shield 2. Washer (2) 2 1 2 1 g026876 Figure 3 1. Front shield 3 2.
Mounting the Side Shields Parts needed for this procedure: 1 Right shield 1 Left shield Procedure 1. Remove the left and right bumpers (Figure 4). Note: Retain the bumpers to use them for securing the shields in place. Figure 5 1. Bumper 4. Hose clamp 2. Nut 3. Bolt 5. Left shield 2. Remove the nut from the hose clamp on the right side of the deck. 3. Install the shields as shown in Figure 4 and Figure 5.
1 Installing the retainer nuts Parts needed for this procedure: 2 2 Retainer nut Procedure Install the retainer nuts to the rear of the deck (Figure 6). 1 1 g026873 Figure 7 1. Retainer nut 2. Pivot bracket 2. Install the pivot bracket onto the gear box (Figure 8). 1 g026888 2 3 4 Figure 6 1. Retainer nut (2) 6 Mounting the Pivot Bracket Parts needed for this procedure: 1 Pivot bracket 2 Bolt (3/8 inch) 2 Lock washer 1. Bolt (3/8 inch) 3. Pivot bracket 1 Retainer nut 2.
7 Mounting the Shield Guide Parts needed for this procedure: 2 Shield guide 4 Flange nut Procedure 1. Remove the left and right plastic covers. Figure 10 Left plastic cover 2. Drill 2 holes—8.7 mm (0.344 inch)—in each plastic cover (Figure 9 and Figure 10). Note: Use Figure 9 and Figure 10 to measure the 8.7 mm (0.344 inch) hole locations on the covers. Align the front hole in each cover with the edge of the step plate. 1. Step plate 5. 3.3 cm (1.31 inch) 2. 8.7 mm (0.344 inch) holes 6. 22.
4. Install a bolt and a push nut to the right plastic cover (Figure 12). 8 Mounting the Right Cover Parts needed for this procedure: Right cover 3 Flange nut 3 Bolt 1 Push nut Procedure Figure 12 1. Plastic cover 2. Bolt 1 1. Remove the right cover shield from the machine. 3. Push nut 2. Drill 2 holes—8.6 mm (0.340 inch)—into the right cover shield (Figure 14). 5. Install a bolt and a push nut to the left plastic cover (Figure 13). Note: Refer to Figure 14 and measure the 8.6 mm (0.
3 2 1 4 5 g026880 Figure 17 1. Left cover shield 4. 9.65 mm (0.380 inches) 2. 2.84 cm (1.12 inch) 5. 8.6 mm (0.340 inch) drill hole 3. 15.2 cm (6 inches) 3. Install 2 retainer nuts onto the left cover (Figure 18). 1 Figure 16 1. push nut 3. Retainer nut 2. Bolt 2 g026882 5. Install the combined covers onto the deck (Figure 16). Figure 18 1. Left cover 9 2. Retainer nuts 4. Install the left cover shield to the left cover (Figure 19).
1 3 g026884 2 1 3 Figure 21 1. Bolts 2. Center cover 11 Figure 20 1. Bolt 3. Retainer nut (previously installed) 2. Push nut Mounting the Shield Support 6. Install the combined covers onto the deck (Figure 20).
Figure 22 1. Flange nut 3. Washer 2. Shield support 4. Hex-head screw (5/16 x 4 inches) Figure 24 1. Bolt 2. Shield support 3. Nut Mounting the Shield Support on a Groundsmaster 360 12 1. On the right side of the machine, remove the nut and the bolt securing the rear frame to the front frame (Figure 23). Mounting the Driveshaft Shield 1 Parts needed for this procedure: 2 g026736 Driveshaft shield 1 Shoulder bolt 1 Washer (0.469 x 0.922 inch) 1 Push nut Procedure Figure 23 1.
Figure 25 1. Shoulder bolt 2. Driveshaft shield 3. Washer (0.469 x 0.922 inch) 4. Push nut 5. Pivot bracket Figure 27 Groundsmaster 360 1. Shield support 2. Install the driveshaft shield through the slot in the shield support installed in procedure 11 Mounting the Shield Support (page 9); refer to Figure 26 or Figure 27. 3. Attach the driveshaft shield to the pivot bracket installed in procedure 6 Mounting the Pivot Bracket (page 5); refer to Figure 25. Figure 26 Groundsmaster 7210 1.
