Form No. 3413-860 Rev A EU Light Kit Serial Number 400000000 and After Groundsmaster® 5900 or 5910 Series Rotary Mower with Cab Model No. 30653—Serial No. 400000000 and Up Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
Procedure 5 6 7 8 9 Description Qty.
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. g038719 Figure 1 2 Disconnecting the Battery No Parts Required Procedure Turn the battery-disconnect switch to the OFF position.
3 Installing the Flasher Module Parts needed for this procedure: 1 Flasher module 1 Wire harness 1 Switch 1 Auxiliary-brake decal g186717 Figure 4 3. Knockout 1. Switch 2. Auxiliary-brake decal 4. Adhere the auxiliary-brake decal above the switch (Figure 4). Procedure 5. Connect the new wire harness to the flasher module, hazard switch, turn-signal switch, and auxiliary-brake switch (Figure 5). 1. Remove the 6 bolts from the console and remove the panel (Figure 3).
4 Installing the Headlights (for Machines with ROPS only) Parts needed for this procedure: 1 Right headlight mount 1 Left headlight mount 2 Cover panel 8 Plug 1 Right headlight assembly 1 Left headlight assembly g035974 Figure 7 Procedure 1. Headlight assembly 1. Unplug the wire harness from each existing headlight. 3. Previously removed fasteners 2. Headlight mount 2. Remove the headlights (Figure 6). 5.
7. Route the wire harness through the bracket and under the operator platform (Figure 8). 8. Connect the wire harness to both connectors that you unplugged from the existing headlights and connect the front turn signal connector to the platform wire harness (Figure 8). 9. Route the wire harness through the left headlight bracket and connect it to the left headlight (Figure 8). 10. Install a cover panel to each headlight mount using 4 plugs.
5. Connect the wire harness to both connectors that you unplugged from the existing headlights and connect the front turn signal connector to the platform wire harness (Figure 10). 6. Route the wire harness through the left headlight bracket and connect it to the left headlight (Figure 10). 7. Secure the wire harness to the brackets using the cable ties.
2.
4. Hold the pivot bracket on the rear of the left frame and drill 3 holes (10 mm or 0.39 inch diameter) in the locations shown in Figure 15. 6. Insert a roll pin in the pivot arm (Figure 17). Note: You will not use the lower front hole in the pivot bracket. g035980 g037878 Figure 17 Figure 15 1. Direction toward the front of the machine 2. Pivot bracket 3. Drill here. 1. Pivot arm 4. Hex-washer bolt (1/4 x 3/4 inch) 2. Spring 5. Roll pin 3. Washer 5.
9. Install the left light to the shroud using 2 bolts (M6 x 30) and 2 nuts (M6) that you removed in 2 (Figure 19). 14. Route the wire harness under the frame of the machine and connect the other end of the tail-light wire harness to the machine wire harness. Note: Use the left tail-light connection that you disconnected in step 1. 15. Install the rear light panel using 4 hex-washer bolts (1/4 x 3/4 inch) as shown in Figure 22. g205340 Figure 19 1. Nut (M6) 2. Bolt (M6 x 30) 10.
8 Installing the Signs and Serial Plate Parts needed for this procedure: 3 Sign 1 Serial plate Procedure 1. Adhere a sign on both sides of the machine (Figure 24). g037889 Figure 25 1. Serial plate, 6 mm (1/4 inch) above the bottom edge of frame 2. Stamp the serial number to the frame here. 4. Secure the serial plate using 4 rivets. 5. Stamp the serial number to the frame, near the serial plate (Figure 25). g205975 Figure 23 1. 1.5 mm (0.06 inches) Note: Use 7 mm (1/4 inch) or larger text. 3.
9 Verifying that the Machine is in CE Mode No Parts Required Procedure 1. Start the machine. 2. From the InfoCenter main menu, navigate to the About screen (Figure 26). g188852 Figure 27 Operation Using the Light and Hazard Switches • Turn the key switch on and press the light switch to the ON position to activate the head lamps. • Press the hazard switch to the ON position to activate the front and rear flashing hazard lights.
Using the Auxiliary-Brake Switch Press and hold the auxiliary-brake switch to decrease the engine speed (Figure 28); release the switch to stop the deceleration and remain at the current engine speed. Note: You may use the switch intermittently to gradually slow the machine. If you press the switch when the engine speed is below 1,200 rpm or if the engine decelerates to 1,200 rpm, the engine shuts off and the machine stops.
Declaration of Incorporation The Toro Company, 8111 Lyndale Avenue South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 30653 Serial No.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
