Form No. 3394-624 Rev A Quick Attach Front Frame Groundsmaster® 360 Multi-Purpose Machine Model No. 30509—Serial No. 315000001 and Up Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Media and Additional Parts Description Use Qty. Installation instructions 1 Use to install kit Parts catalog 1 Use to reference part numbers Lock pin 1 Use to secure the attachment to the lift frame Hair pin cotter 1 Use to secure the attachment to the lift frame Note: The Groundsmaster 360 must be equipped with the Electrical Accessory Kit, Part 115-0019, to operate the Quick Attach Front Frame Kit. 1 Removing the Cutting Deck No Parts Required Procedure Figure 1 1.
Figure 3 1. Gearbox 2. PTO drive shaft end yoke • Loosen the 2 capscrews and lock nuts (Figure 3). • Slide the drive shaft end yoke from gearbox shaft and tie them up to the frame for support. Figure 2 8. Remove the 4 ring pins and clevis pins that secure the deck lift chains to the adjustment clevises on the cutting deck (Figure 1). 1. Height of Cut pin 4. Position suitable furniture dollies under the cutting deck. 9. Roll the cutting deck away from the machine. 5.
Figure 5 g015534 1. Front attachment frame Figure 4 1. Shorter hydraulic tube 3. Longer hydraulic tube 2. Valve 4. Manifold 2. Screw, 1/2 x 1-1/4 inch and a 1/2 inch flange nut 3. Screw, 1/2 x 4-1/2 inch 5. Screw, 1/2 x 3–1/4 inch, 2 support washers and lock nut, 1/2 inch 6. Lock pin 7. Hair pin cotter 4. Spacer 3 2. Guide the shorter hydraulic tube assembly (Figure 4) around and above the traction control rod. Mounting the Front Attachment Frame 3.
. On the front of the attachment, secure the outer hole, on each side, to the frame channels with a 1/2 x 4-1/2 inch screw and a 1/2 inch flange nut (Figure 6). 4 6. On the rear of the attachment, loosely install each side to the frame channels with 2 1/2 x 1-1/4 inch screws and 1/2 inch flange nuts (Figure 6). Installing the Hydraulic Tube Assemblies 7.
Figure 10 1. Drive shaft Figure 9 2. Jack shaft 1. Shorter hydraulic tube 5. Tube clamp, small 2. Secure the drive shaft to the jack shaft with the roll pin previously removed. 2. Valve 6. Tube clamp, large 3. Tighten the 2 drive shaft cap screws and lock nuts. 3. Longer hydraulic tube 7. Plate, small 4. Manifold 8. Plate, large 6 4. Connect the rear end of the longer hydraulic tube to the tube on the machine (Figure 9). Installing the Switches 5. Tighten connections. 6.
Think Safety First Please read all safety instructions and symbols in the safety section. Knowing this information could help you or bystanders avoid injury. G015952 1 DANGER 2 Operating on wet grass, ice or slippery steep slopes can cause sliding and loss of control. Wheels dropping over edges can cause roll overs, which may result in serious injury, death or drowning. Read and follow the rollover protection instructions and warnings. Figure 11 1. Switches. 2.
Never operate the PTO with attachment in the raised position. Noise from the PTO drive line will be evident. 2 Install the attachment as follows: • Remove any attachment from the machine. Follow attachment supplier's recommendation for safe blocking and storage. • Drive the machine into position behind the attachment adapter. Raise the machine adapter into the attachment adapter. • Secure the adapters together with the attachment pin and hairpin cotter as shown in Figure 14.
Attaching the deck 1. If the deck chains were removed from the lift arms, reinstall them. 2. Raise the drag-links on the deck with a pry bar and place a block (6 x 2 x 4 inch) under each one to lift the arm up. Use caution, as there will be energy stored in the torsion spring. 3. Raise the front of the machine so there is enough clearance to slide the deck underneath, and line up slots with the drag-link. 4. Slowly lower the machine over the drag links until the holes line up in the frame.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • Torque the frame mounting bolts. • Torque wheel lug nuts. Every 50 hours • Lubricate grease fittings Every 200 hours • Torque wheel lug nuts. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance.
Checking the Fuses Storage Refer to the Operator's Manual supplied with the cab for instructions on fuses. Machine If the machine has any electrical system issues, check the fuses. Grasp each fuse and remove them one at a time, checking to see if any are blown. If you need to replace a fuse, always use the same type and amperage rated fuse as the one you are replacing, otherwise you could damage the electrical system. 1.
Notes: 12
Notes: 13
Declaration of Incorporation Model No. 30509 Serial No. Product Description Invoice Description General Description Directive 315000001 and Up Quick Attach Front Frame, Groundsmaster 360 Multi-Purpose Machine FRONT FRAME, QAS-4WD GM360 Quick Attach Front Frame 2006/42/EC, 2000/14/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
