Operator's Manual
Table Of Contents
- NO TITLE
- NO TITLE
- 1 Checking Tire Pressure
- 2 Servicing the Battery
- 3 Servicing the Engine
- 4 Servicing the Transmission Hydraulic Oil
- 5 Servicing the Auxiliary Hydraulic Oil
- 6 Removing Cylinder Stop (for model 33518)
- NO TITLE
- NO TITLE
- Lubricate Chains
- Lubricate Grease Fittings
- Lubricate Caster Wheel Hubs
- Service Air Cleaner
- Change Engine Oil
- Check Spark Plugs
- Check Spark Arrester (if equipped)
- Change Fuel Filter
- Check Battery Charge
- Recommended Jump Starting Procedure
- Check Tire Pressures
- Check Wheel Hub Nuts Torque Specification
- Check Wheel Lug Nuts Torque Specification
- Check Condition Of Chains
- Check Condition Of Sprockets
- Check Transmission Output Shaft Nut Torque Specification
- Jackshaft Drive Chain Tension Adjustment
- Drive Wheel Chain Tension Adjustment
- Caster Pivot Bearings Pre-Load Adjustment
- Adjusting the Parking Brake
- Adjusting the Brake Switch
- Check Condition and Tension Of Belts
- Transmission Drive Belt Tension
- Auxiliary Pump Drive Belt Adjustment
- Motion Control Linkage Adjustment
- Check Auxiliary Hydraulic Oil Level
- Check Hydraulic Transmission Oil Level
- Change Auxiliary Hydraulic Reservoir Fluid and Filter
- Change Hydraulic Transmission Filters and Fluid
- Tine Maintenance
- Clean Engine and Exhaust System Area
- Remove Engine Shrouds and Clean Cooling Fins
- Clean Debris From Machine
- Waste Disposal
- NO TITLE
CheckTransmissionOutput
ShaftNutTorqueSpecication
ServiceInterval:Yearly
Torquethenutonthetransmissionoutputtaperedshaftto
285-353N-m(210-260ft-lb).
JackshaftDriveChainTension
Adjustment
1.Stopengine,waitforallmovingpartstostop,and
removekey.Engageparkingbrake.
2.Lifttherearoftheunitandsupportusingjackstands
orequivalentsupport.
3.Checkthechainsonbothsidesoftheunitforproper
tension.Thechainsshouldbeabletomoveupand
down6-12mm(1/4-1/2inch).
4.Loosenthenutsonthethreehydromountingbolts
andthetwoontheadjustmentboltasshownin
Figure
16.Thenutsonthehydromountingboltsmustbe
loosenedonbothsidesoftheunit.
Figure16
1.Hydromountingboltsand
nuts
4.6-12mm(1/4-1/2inch)
2.Nuts
5.Guardremovedforclarity
3.Adjustmentbolt
5.Turntheadjustmentbolttomovetransmission
adjustmentplatesandhydros.Tightenthenutson
bothsidesoftheadjustmentboltswhenthechainsare
properlytensioned.
6.Tightenhydromountingbolts.
7.AdjustmotioncontrolsasstatedintheMotionControl
LinkageAdjustment(page31)section.
DriveWheelChainTension
Adjustment
1.Stopengine,waitforallmovingpartstostop,and
removekey.Engageparkingbrake.
2.Lifttherearoftheunitandsupportusingjackstands
orequivalentsupport.
3.Checkthechainsonbothsidesoftheunitforproper
tension.Thechainsshouldbeabletomoveupand
down6-12mm(1/4-1/2inch).
4.Adjusttheidlersprockets.
5.Recheckthechaintensionandtightentheidlerbolt.
CasterPivotBearings
Pre-LoadAdjustment
Removedustcapfromcasterandtightennylocnutuntil
washersareatandbackoff1/4ofaturntoproperlyset
thepre-loadonthebearings.Ifdisassembled,makesurethe
springdiscwashersarereinstalledasshowninFigure17.
Figure17
1.Springdiscwashers
29