Form No. 3446-562 Rev A Backhoe Fit-Up Kit TX 1000 Compact Tool Carrier Model No. 23126 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 © 2021—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty. No parts required – Prepare the machine.
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Lower the loader arms. 4. Shut off the engine, remove the key, and allow the machine to cool. 5. Open the rear-access cover and engine hood. 6. Turn the battery-disconnect switch to the OFF position. 7. Remove the air cover by removing the 3 bolts holding it in place (Figure 1). Note: Retain the air cover and corresponding bolts for later installation.
2 Replacing the Tilt-Cylinder Pin Parts needed for this procedure: 1 Tilt-cylinder pin Procedure 1. Tilt the traction unit attachment mount plate flat and gently rest the attachment mount plate on top of a block. 2. Place a block in front of the mount plate so that it cannot swing forward when you remove the tilt-cylinder pin. CAUTION When you remove the tilt-cylinder pin, the mount plate may swing forward, crushing your feet or hands, or those of bystanders.
g351625 Figure 2 1. Bolt 4. New tilt-cylinder pin 2. Tilt cylinder 5. Middle hole 3. Nut 3 Installing the Quick-Attach Plate and Tie-Down Links Parts needed for this procedure: 1 Quick-attach plate 2 Small bolt 8 Large bolt 24 Washer 8 Spacer 10 Nut 2 Tie-down link 4 Pin lock Procedure 1. Install the quick-attach plate onto the backhoe using 2 small bolts, 8 large bolts, 24 washers, 8 spacers, and 10 nuts (Figure 3). Torque the bolts to 94 to 102 Nm (70 to 75 ft-lb).
g352074 Figure 3 1. Small bolt (2) 4. Spacer (8) 2. Large bolt (8) 5. Nut (10) 3. Washer (24) 2. 3. 4. Connect the traction unit receiver plate to the backhoe quick-attach plate and engage the quick-attach pins; refer to the traction unit Operator’s Manual. Install a tie-down link as shown in Figure 4. Secure the tie-down link with 2 pin locks. Repeat step 3 on the other side of the machine. g352719 Figure 4 1. Pin locks (4) 2.
5. Connect the hydraulic hoses; refer to the traction unit Operator’s Manual. 4 Installing the Wire Harness Parts needed for this procedure: 2 Jumper wire (for use on traction units with serial number 3999999999 and below only) 1 Fit-up kit electrical harness 1 Electrical harness cap 4 Cable tie Procedure Note: Use the jumper wires on traction units with serial number 3999999999 and below only. 1. Plug the fit-up kit harness connector into the backhoe electrical harness connector (Figure 5).
g355376 Figure 6 B. Under the control panel, remove the traction unit harness terminal from the ignition switch (Figure 7). g355397 Figure 7 1. Ignition switch 2.
C. Plug the traction unit harness ignition terminal into the corresponding jumper terminal (Figure 8). D. Plug the other jumper terminal into the ignition switch (Figure 8). g355400 Figure 8 1. Ignition switch 3. Jumper terminal (to traction unit harness ignition terminal) 2. Jumper terminal (to ignition switch) 4.
For traction units with serial numbers 4000000000 and up: A. Under the control panel, remove the traction unit harness connector from the ignition switch (Figure 9). g355402 Figure 9 1. Ignition switch 2. Traction unit harness connector B. Plug the traction unit harness connector into the fit-up kit harness connector (Figure 10). C. Plug the other fit-up kit harness connector into the ignition switch (Figure 10). g355403 Figure 10 1. Ignition switch 3.
g355414 Figure 11 3. To light kit connection 1. Cable tie 2. To main harness light kit connection 8. Route the rest of the harness down the inside of the traction unit frame alongside the traction unit wire harness as shown in Figure 12. g352195 Figure 12 9. Lift the back of the machine off the ground. Support the machine using jack stands. Note: Use jack stands rated for your machine. WARNING Mechanical or hydraulic jacks may fail to support the machine and cause serious injury.
g355575 Figure 13 1. Bottom cover 11. Connect the remaining 2 connectors into the main harness parking brake switch connection and the parking brake (Figure 14). g352196 Figure 14 1. To parking brake 2.
. Secure the harness to the traction unit wire harness with the 2 remaining cable ties as shown in Figure 15. g352465 Figure 15 1. Cable tie 13. Install the bottom cover and the 2 corresponding bolts removed in Step 10. 14. Install the air cover with the 3 corresponding bolts removed in Step 7 of 1 Preparing the Machine (page 2). 15. Close the rear-access cover and engine hood.
