Setup Instructions

ManualsBrandsToro ManualsCompact LoaderToro 22979HD

FormNo.3432-587RevA

Trailer

TRXTrencherorSTXStumpGrinder

ModelNo.22979

ModelNo.22979HD

SetupInstructions

Safety

Readandunderstandthefollowingbeforeusingthe

trailer.

•Beforeeveryuse:

–Inspectthecoupler,ball,andhitch.

–Alwaysusesafetychains.

–Verifythatalllightsarefunctioningproperly.

–Verifythatthetiresareproperlyinatedas

recommendedontires.

–Verifythatthelugnutsaretightandtorqued

properly.

–Verifythatthatthemachineisproperlysecured.

•Knowhowtoproperlycontrolyourtowing

vehicle/trailercombinationonthehighwayunder

allconditions.Rememberthattheloadedweight

ofthetrailerincreasesyourbrakingandstopping

distances.

•Youareresponsiblefordeterminingthetowing

capacityofyourvehicle.

•Cleanoffthemachinespriortoloadingthem

ontothetrailer.Keepthetrailercleanofloose

debristhatcouldfalloffduringtransport,causinga

hazard.

•Useproperloadingandunloadingprocedures

andsequences.Readallmanualsandfollowthe

instructionsprovided.

•Inspectthetrailerandmachineoftenduring

transport.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal140-1123

140-1123

1.Warning—readtheOperator’sManual;maximumweight

of676kg(1,492lb).

decal133-8061

133-8061

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3432-587*A

Summary of content (12 pages)

PAGE 1
Form No. 3432-587 Rev A Trailer TRX Trencher or STX Stump Grinder Model No. 22979 Model No. 22979HD Setup Instructions Safety Read and understand the following before using the trailer. • Before every use: all conditions. Remember that the loaded weight of the trailer increases your braking and stopping distances. • You are responsible for determining the towing capacity of your vehicle. • Clean off the machines prior to loading them – Inspect the coupler, ball, and hitch.
PAGE 2
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. Trailer bed Wheel Lug nuts Tongue Bolt (5/8 x 3 inches) Nut (5/8 inch) Mounting strap Jack Bolt Locknut Chain Ramp Bolt (1/2 x 1-1/2 inches) Nut (1/2 inch) Ramp strap Cotter pin (1-1/4 inch) 1 2 10 1 2 2 2 1 4 4 1 1 2 2 2 2 Install the trailer jack. No parts required – Test the wire harness. Install the wheels. Attach the tongue. Install the ramp.
PAGE 3
2 Attaching the Tongue Parts needed for this procedure: 1 Tongue 2 Bolt (5/8 x 3 inches) 2 g008364 Figure 3 Nut (5/8 inch) 1. Tongue 3. Wire harness 2. Opening 4. Wire (secured to harness) 5. Procedure 1. Lay the tongue out in front of the trailer and locate a flexible wire longer than the tongue. 2. Feed the wire through the length of the tongue so a portion of the wire is visible at both ends (Figure 2).
PAGE 4
3 Installing the Trailer Jack (Model 22979) Parts needed for this procedure: g008366 Figure 5 2 Mounting strap 1 Jack 1. Trailer (underside) 4. Wire harness 4 Bolt 2. Tongue 5. Bolt (5/8 x 3 inches) 4 Locknut 3. Bolt holes 8. Procedure At the front end of the tongue, pull the wire harness forward to remove all slack in the harness before continuing the installation. 1. Place the jack against the tongue (Figure 7).
PAGE 5
4 Installing the Ramp Parts needed for this procedure: 1 Chain 1 Ramp 2 Bolt (1/2 x 1-1/2 inches) 2 Nut (1/2 inch) 2 Ramp strap 2 Cotter pin (1-1/4 inch) Procedure 1. Install the retaining chain from the bed of the trailer to the retaining pin (Figure 8). g008369 Figure 9 1. Trailer bed 4. Nut (1/2 inch) 2. Ramp 5. 0.16 cm (1/16 inch) gap 3. Bolt (1/2 x 1-1/2 inches) 3. g008368 Figure 8 1. Trailer bed 4. Retaining pin 2. Loop 5.
PAGE 6
g008372 Figure 11 g008371 Figure 10 1. Lynch pin 2. Post on ramp 5. Post on bed 6. Cotter pin 3. Wiring harness 2. Holster 4. Ramp 3. Ramp strap 5. 1. Tongue Operation Raise the ramp and use the straps and lynch pins to secure it in the transport position (Figure 10). Operating the Jack Turn the crank clockwise to lower the jack (Figure 12). 5 Testing the Wire Harness No Parts Required Procedure 1. Locate the white ground wire on the wiring harness and ground bolt on the front of the tongue.
PAGE 7
Attaching the Trailer This trailer uses couplers that require a 2 inch ball for the hitch. 1. Rotate the jack into the vertical position (Figure 14). 2. Raise the trailer to above the ball hitch. 3. Lift the handle on the tongue. 4. Lower the tongue ball socket over the ball hitch (Figure 15). g022034 Figure 13 Pull out on the handle to rotate the jack (Figure 14). g008373 Figure 15 1. Tongue 4. Auxiliary chains 2. Ball socket 5. Locking pin (not included with the trailer) 3.
PAGE 8
Loading the Trencher CAUTION Attempting to load or unload the machine from a trailer that is not securely hitched to a suitable vehicle could cause the trailer to become unstable, and tip causing injury to you or bystanders. Make sure the trailer is securely hitched to a suitable vehicle parked on a level surface before attempting to load or unload the machine. 1. 2. g008375 Figure 17 1. Forward stop 2. Guide rails Remove the retaining straps and lower the ramp to the ground. 7.
PAGE 9
DANGER The ramp in the transport position represents a stored energy hazard and if not secured can fall; injuring you or bystanders. Hold the ramp in place when removing straps and use care to lower the ramp carefully to the ground. 2. Remove the pin on the hold down bar and lay the chain and pin on the center of the trailer bed. Slide the hold down bars apart. 3. Start the machine according to the Operator's Manual and disengage the parking brake. 4. Raise the trencher arm into the transport position.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12