Form No. 3429-947 Rev B Brush Cutter TXL 2000 Tool Carrier Model No. 22534—Serial No. 318000001 and Up Register at www.Toro.com.
WARNING Model No. CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Serial No. This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.
Safety • Establish your own procedures and rules for General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious injury or death. • Do not raise the loader arms while this attachment is installed; always keep the attachment close to the ground, with the loader arms retracted, and the chains installed. • Read and understand the content of this Operator’s Manual before starting the engine.
Maintenance and Storage Safety Safety and Instructional Decals • Check fasteners at frequent intervals for proper Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. tightness to ensure that the equipment is in safe operating condition.
Product Overview Operation Determine the left and right sides of the machine from the normal operating position. Installing and Removing the Attachment Refer to the Operator’s Manual for the traction unit for the installation and removal procedure. Important: Before installing the attachment, position the machine on a level surface, ensure that the mount plates are free of any dirt or debris, and ensure that the pins rotate freely. If the pins do not rotate freely, grease them.
Transport Position CAUTION Hydraulic couplers, hydraulic lines/valves, and hydraulic fluid may be hot. If you contact hot components, you may be burned. When transporting an attachment, keep the attachment as close to the ground as possible, no more than 15 cm (6 inches) above the ground, and keep the loader arms retracted. Tilt it rearward. • Wear gloves when disconnecting the hydraulic couplers. • Allow the machine to cool before touching hydraulic components. • Do not touch hydraulic fluid spills.
Operating Tips • Do not cut material larger than 7.6 cm (3 inches) in diameter. • To reverse the direction that the blades rotate, reverse the flow of hydraulics. • Engage the hydraulics with the throttle at LOW IDLE. When the blades rotate smoothly, increase the throttle to HIGH IDLE. Important: Do not cut material until the blades rotate smoothly. • If the blades slow under load, decrease the traction speed or cut less material to maintain blade speed.
Maintenance Determine the left and right sides of the machine from the normal operating position. CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance. Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Every 50 hours Maintenance Procedure • Grease the machine. • Check the planetary fluid level.
Checking the Planetary Fluid Level Servicing the Cutting Blades Service Interval: Before each use or daily Blade Safety Fluid Type: 80W-90 Gear Oil, API-GL-5 approved A worn or damaged blade can break, and a piece of the blade could be thrown at you or bystanders, resulting in serious personal injury or death. Capacity: 0.41 L (14 fl oz) 1. Park the machine on a level surface, engage the parking brake, and lower the loader arms. 2. Shut off the engine and remove the key. 3.
Replacing the Blades Sharpening the Blades Replace the blades if they hit a solid object, are out of balance, or are bent. Remove the blades as described in Replacing the Blades (page 10) and use a file to sharpen the cutting edge at the end of the blade (Figure 11). Important: Replace all the blades at the same Note: Maintain the original angle. Ensure the cutting time to maintain consistent wear and weight balance. 1. edge is 0.8 to 1.6 mm (1/32 to 1/16 inch) thick.
Storage 1. Before long-term storage, wash the attachment with mild detergent and water to remove dirt and grime. 2. Paint all scratched or bare metal surfaces. Note: Paint is available from your Authorized Service Dealer. 3. Store the attachment in a clean, dry garage or storage area. Cover it to protect it and keep it clean.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
