FORM NO. 3322–648 Multi-Purpose Tool Sitework Systems Attachment Model No.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stability Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loose Parts . . . . . . . . . . . . .
WARNING CAUTION POTENTIAL HAZARD • When the engine is off, attachments in the raised position can gradually lower. POTENTIAL HAZARD • If you step off of the platform with the load raised, the machine could tip forward. WHAT CAN HAPPEN • Someone nearby may be pinned or injured by the attachment as it lowers. WHAT CAN HAPPEN • Someone nearby may be pinned or injured. HOW TO AVOID THE HAZARD • Lower the load before stepping off or the platform.
Scarifier teeth (3) Width (with tip) 2.0 inches (5.1 cm) Width (without tip) 0.63 inches (1.6 cm) Length 13.0 inches (13.0 cm) Height 11.7 inches (29.7 cm) Weight (each) 9.0 lbs (4.1 Kg) Tips Replaceable, cast iron spear points Ball hitch (1, ball not included) (Suitable for mounting balls with 1 inch (2.5 cm) diameter mounting studs) Width 3.0 inches (7.6 cm) Length 8.4 inches (21.3 cm) Height 9.4 inches (23.9 cm) Weight 7.5 lbs (3.
Stability With an Unloaded Boom Jib Orientation Stability With the Scarifier Teeth Orientation Stability Rating Front Uphill Rear Uphill Side Uphill Stability Rating Front Uphill E D Rear Uphill B B Side Uphill B IMPORTANT: The multi-purpose tool with the boom jib installed is rated for use with the counterweight. Do not use the boom jib without the counterweight or the traction unit will become unstable.
3. Slowly push the attachment tilt lever forward to tilt the mount plate forward. 1 4. Position mount plate into the upper lip of the receiver plate on the frame (Fig. 2). 1 3 2 2 4 m–4055 m–3929 Figure 2 1. Mount plate Figure 4 2. Receiver plate 1. Frame 2. Accessory 5. Raise the loader arms while tilting back the mount plate at the same time. 3. Clevis pin 4. Hairpin cotter” 4. Repeat steps 1 through 3 for the remaining accessory positions if needed.
Scarifier/Ripper Operation Operation The multi-purpose tool can be used in 3 different operating modes, as follows: • Boom jib (Fig. 5) • Scarifier/ripper (Fig. 6) • Hitch (Fig. 7) Boom Jib Operation m–3941 Figure 6 With the scarifier teeth installed, the multi-purpose tool can be used to loosen hard packed ground. Lower the teeth to the ground by lowering the attachment arms and tilting the attachment plate forward. Move the traction unit slowly backward while lowering the teeth into the ground.
When crossing on or near a public road or street, always follow traffic laws and regulations, especially those pertaining to slow moving vehicles. The traction unit and accessories are not designed for use on public roads or streets. WARNING POTENTIAL HAZARD • Pulling trailers or other objects using a rope, chain or cable can cause the rope, chain, or cable to break under tension. WHAT CAN HAPPEN • The rope, chain, or cable could break and snap back, causing serious injury.
