Installation Instructions

ManualsBrandsToro ManualsSprayersMulti Pro WM Turf Sprayer Finishing Kit, Manual Workman Utility Vehicle

FormNo.3389-137RevA

MultiPro

WMTurfSprayerFinishingKit

ManualWorkman

UtilityVehicle

ModelNo.131-3302

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Drive-shaft-shieldbracket

Installthedrive-shaftshieldonthe

sprayerpump.

PTOdriveshaft

Woodruffkey

Setscrew

Drive-shaftshield

Clip

Flange-headbolt(1/4x3/4inch)

InstallthePTOshaftandthedrive-shaft

shieldtothesprayerpump.

Hydraulichose(5/8x55.6inches)

Hydraulichose(5/8x85.2inches)

Malequickcoupler1

Femalequickcoupler1

Tubeclamp2

Clampbolt(5/16x1-1/2inches)

Cabletie

Installthehydraulichosesfortheboom

liftcylinders.

Nopartsrequired

–

CouplethePTOshafttothetransaxle.

Note:Removethecargoboxoratbedfromthevehiclebeforeinstallingthiskit;refertotheOperator’sManualforthevehicle.

Note:ForNon-TCmodels,installtheRearPTOKitbeforeinstallingthiskit;contactyourAuthorizedToroDistributor

aboutpurchasingthiskit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3389-137*A

Summary of content (8 pages)

PAGE 1
Form No. 3389-137 Rev A Multi Pro® WM Turf Sprayer Finishing Kit Manual Workman® Utility Vehicle Model No. 131-3302 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
PAGE 2
1 Installing the Drive-Shaft-Shield Bracket on the Sprayer Pump Parts needed for this procedure: 1 Drive-shaft-shield bracket Procedure 1. Remove the 2 bolts at the left and right of the input shaft of the sprayer pump (Figure 1). Figure 2 1. Drive-shaft-shield bracket 2. Bolts from the sprayer pump 4. Torque the bolts to 23 to 26 N-m (17 to 21 ft-lb). 2 Install the PTO Shaft and the Drive-Shaft Shield to the Sprayer Pump Parts needed for this procedure: Figure 1 1. Bolts 2.
PAGE 3
Figure 3 1. Woodruff key 2. Slot Figure 5 1. Flange-head bolt (2) 2. Apply anti-seizing compound to the pump shaft and the Woodruff key. 3. Drive-shaft shield 2. Clip (2) 3. Remove the 2 set screws on the PTO shaft end (Figure 4). 3 Installing the Hydraulic Hoses for the Boom Lift Cylinders Parts needed for this procedure: Figure 4 1. PTO shaft end 3. Shaft of the sprayer pump 2. Set screw (2) 4. Apply medium-duty, thread-locking compound to the 2 set screws on the PTO shaft end.
PAGE 4
. Remove the cap from the T-fitting in the hydraulic tube next to the transmission-oil filter (Figure 8). Figure 6 1. Female end of hose 2. Male quick-connect coupler 3. Male end of hose 4. Female quick-connect coupler Figure 8 2. Assemble the female quick-connect coupler onto the hose (3/8 x 56-1/2 inches) as shown in Figure 6 and torque the coupler to 37 to 45 N-m (27 to 33 ft-lb). 1. T-fitting 2. Transmission-oil filter 5. Connect the free end of the hose (3/8 x 55.
PAGE 5
4 Coupling the PTO Shaft to the Transaxle No Parts Required Procedure 1. At the front yolk of the PTO drive shaft, align the socket of the front yolk with the splines of the PTO output shaft on the transaxle (Figure 10). Figure 10 1. Spring lock 3. PTO output shaft 2. PTO drive shaft 2. Pull the spring lock (rubber cowling) at the front yolk of PTO drive shaft rearward (Figure 10). 3. Slide the socket of the front yolk over the output shaft splines (Figure 10). 4.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8