Installation Instructions

ManualsBrandsToro ManualsRiding ProductsLight Kit, Sand Pro 2040Z Traction Unit

FormNo.3378-606RevA

LightKit

SandPro

2040ZTractionUnit

ModelNo.08721

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Wireharness1

Cabletie

LEDLight2

Screw,5/16x2–3/4inch

Screw,5/16x3–1/2inch

Screw,5/16x4–1/2inch

Pivotwasher,5/16x1–1/8inch

Flatwasher,3/8x7/8inch

Flangenut,5/16inch

Lightbracket1

Selftappingscrew,5/16x3/4inch

R-clamp1

Rockerswitch1

Fuse,15amp1

Installationinstructions1

Partscatalog1

Installthelightkit

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3378-606*A

Summary of content (8 pages)

PAGE 1
Form No. 3378-606 Rev A Light Kit Sand Pro® 2040Z Traction Unit Model No. 08721 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1. Position the machine on a level surface, lower the attachment, stop the engine, engage the parking brake and remove the key from the ignition. 2 1 3 2. Disconnect the negative battery cable from the battery. 3. Mount the front light to the machine as follows: • Remove the screw, washer and nut mounted to the light bracket (Figure 1). Discard the screw. 4 6 2 1 5 G023890 Figure 2 3 7 4 6 1. Nut 4. Light 2. Screw, 5/16 inch 3. Flat washer 5. Screw 6.
PAGE 3
7. Remove the cable tie securing the wires to the corner of the console. 1 8. Remove and discard the hole plug from the control panel (Figure 6). 2 2 1 3 G023891 G024038 Figure 4 Figure 6 1. Seat assembly 1. Hole plug 5. Remove the cable tie securing the seat switch wire to the seat support, unplug the seat switch wires and remove the seat from the machine. 6. Remove the (4) screws securing the control panel to the console (Figure 5). Retain the screws. 1 2. Switch 9.
PAGE 4
1 20. Slip the R-clamp onto the wire harness (Figure 8). 21. Mount the light bracket and the R-clamp to the ROPS post with (2) self tapping screws (5/16 x 3/4 inch) (Figure 8). 22. Mount the rear light to the light bracket with the fasteners supplied with the light (Figure 8). 23. Plug the wire harness connector into the light. Important: Make sure the wire harness is away from any hot or rotating components and avoid any possible pinch points. 1 24.
PAGE 5
Notes: 5
PAGE 6
Notes: 6
PAGE 7
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
PAGE 8