Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSpeed Limiter Kit, Sand Pro 2040Z Traction Unit

FormNo.3378-593RevA

SpeedLimiterKit

SandPro

2040ZTractionUnit

ModelNo.08720

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Safety

WARNING

Ifyoudrivethemachinewithoutanattachment

installed,itcantipoverandinjuresomeoneor

damageproperty.

DonotdrivethemachinewithoutaToro-approved

attachmentinstalled.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Liftbracket(left-hand)

Liftbracket(right-hand)

Locknut(1/2inch)

Installtheliftbrackets.

Cable

Cambracket(left-hand)

Cambracket(right-hand)

Installthecablesontothecambrackets.

Cam

Socket-headcapscrew

Jamnut2

Flangebushing2

Spacer(3/8x17/32inch)

Bolt(3/8x1-1/4inch)

Fenderwasher(3/8inch)

Locknut(3/8inch)

Installthecams.

Bolt(5/16x3/4inch)

Flangenut(5/16inch)

Camspring

Installthecambrackets.

Cabletie

Bolt(5/16x3-1/2inch)

Frictionwasher4

Spacer(5/16x3/8inch)

Spacer(5/16x1inch)

Flangenut(5/16inch)

Routeandmountthecables.

Nopartsrequired

–

Checktheoperationoftheattachment

lift.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-593*A

Summary of content (12 pages)

PAGE 1
Form No. 3378-593 Rev A Speed Limiter Kit Sand Pro® 2040Z Traction Unit Model No. 08720 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. WARNING If you drive the machine without an attachment installed, it can tip over and injure someone or damage property. Do not drive the machine without a Toro-approved attachment installed.
PAGE 2
Procedure Description 7 8 Use Qty. No parts required – Adjust the speed and the tracking. No parts required – Install the stop plates. 1 1 Installing the Lift Brackets 2 3 Parts needed for this procedure: 1 Lift bracket (left-hand) 1 Lift bracket (right-hand) 2 Locknut (1/2 inch) 4 G024661 Figure 2 Left-hand side shown Procedure 1. Remove the top nut securing the left-hand side of the rollover protection system (ROPS) to the machine frame (Figure 1).
PAGE 3
2 3 Installing the Cables onto the Cam Brackets Installing the Cams Parts needed for this procedure: Parts needed for this procedure: 2 Cam 2 Cable 2 Socket-head cap screw 1 Cam bracket (left-hand) 2 Jam nut 1 Cam bracket (right-hand) 2 Flange bushing 2 Spacer (3/8 x 17/32 inch) 2 Bolt (3/8 x 1-1/4 inch) 4 Fender washer (3/8 inch) 2 Locknut (3/8 inch) Procedure 1. Remove the jam nut nearest the visible internal part of the cable (Figure 4). 1 Procedure 2 1.
PAGE 4
1 2 3 1 2 3 4 G024658 Figure 6 G024657 Figure 8 3. Flange bushing 1. Cam 2. Spacer (3/8 x 17/32 inch) 3. Use tape or a marker to mark the exact locations of the stop plates (Figure 7). 3. Bolt (3/8 x 1-1/4 inch) 2. Fender washer (3/8 inch) 4. Cam 6. Secure the cam with a 3/8 x 1-1/4 inch bolt, 2 fender washers, and a 3/8 inch locknut. Important: If the stop plates are not aligned correctly, the control handles could overload the input shafts of the transmissions. 1 1.
PAGE 5
1 1 2 3 3 G024656 Figure 9 1. Bolts (5/16 x 3/4 inch) 2 3. Flange nuts (5/16 inch) G024718 Figure 11 2. Cam bracket 1. Tab 2. Spring 2. Secure the bracket with 2 bolts (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch). 6. Hook the other end of the spring over the tab on the cam bracket (Figure 11). 3. Rotate each cam toward the center of the machine (Figure 10). 1 3.
PAGE 6
1 1 3 2 1 3 4 1 G024654 Figure 14 G024664 Figure 12 Some parts shown as transparent 1. Cable tie 2. Control-lever damper 3. Cable 4. Hole 1. Cable (left-hand side shown) 3. Use a cable tie to secure each cable to the control-lever damper on each side (Figure 14). 1 4. Install each cable to the corresponding lift bracket as follows (Figure 15): A. Slide the bellows away from the threaded fitting. B. Remove the jam nut nearest the visible part of the cable. C.
PAGE 7
1 2 3 7 4 Adjusting the Speed and the Tracking 6 No Parts Required 5 G024652 Adjusting the Speed Figure 16 Left-hand side shown 1. Flange nut (5/16 inch) 4. Bolt (5/16 x 3-1/2 inch) 2. Spacer (5/16 x 1 inch) 5. Friction washers 3. Spacer (5/16 x 3/8 inch) 6. Spring 1. Loosen the jam nut on the socket-head cap screw on each cam (Figure 17). 1 2 6. Install the assembled bolts and cables to the attachment lift, and secure them with 2 flange nuts (5/16 inch); refer to Figure 16.
PAGE 8
Adjusting the Full-speed Tracking Operation If you need to adjust the full-speed tracking, refer to the machine Operator’s Manual. Using the Speed Limiter Kit If you lower the attachment while driving over a certain speed, the cam does not limit the driving speed until you manually decrease the speed by moving the control handles accordingly.
PAGE 9
Notes: 9
PAGE 10
Notes: 10
PAGE 11
Notes: 11
PAGE 12
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 08720 Serial No.