Form No. 3378-554 Rev B Nail Drag Sand Pro® 2040Z Traction Unit Model No. 08717—Serial No. 314000001 and Up G023933 Register at www.Toro.com.
WARNING Figure 2 CALIFORNIA Proposition 65 Warning 1. Safety alert symbol This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. Contents Introduction Introduction .................................................................. 2 Setup ........
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Description Drawbar Support brace Stop-chain assembly Bolt (3/8 x 4-1/2 inches) Bolt (3/8 x 3/4 inch) Locknut (3/8 inch) Long spacer Bolt (5/16 x 3/4 inch) Flange locknut (5/16 inch) U-bolt Lift chain Washer (3/8 inch) Nail Use Qty. 1 2 1 2 4 6 2 2 4 1 2 2 88 Assemble the nail drag.
Assembling the Nail Drag 1 2 3 Removing the Plates 1. Remove the lynch pins from the 8 clevis pins securing the nail plate and the top plates to the bottom plate (Figure 3). 4 Note: Retain the lynch pins for installing the nail plate and the top plates. 1 G023745 Figure 4 2 1. Long spacer (2) 3. Long bolt (3/8 x 4-1/2 inches), 2 2. Locknut (3/8 inch), 4 4. Short bolt (3/8 x 3/4 inch), 2 2.
Attaching the Support Braces 1. Mounting the Stop-chain Assembly Align the longer flat end of a support brace to the underside of the bottom plate so that the shorter flat end reaches the drawbar (Figure 5). 1. Align the center tab on the drawbar bracket to the hole toward the rear of the drawbar (Figure 7). 1 1 2 3 2 4 3 5 G023948 Figure 7 G023946 Figure 5 1. Flange locknut (5/16 inch) 3. Bolt (5/16 x 3/4 inch) 2. Support brace 4. Drawbar 2. Drawbar bracket 3. Center tab 5. U-bolt 2.
Mounting the Lift Chains 1. Insert a bolt (3/8 x 3/4 inch) through a lift chain, and secure it to the bottom plate with a washer (3/8 inch) and a locknut (3/8 inch); refer to Figure 8. Note: To ensure that the chain lengths do not change by rotating, ensure that the second link of the chain stays in the slot above the bolt hole, as shown in Figure 8. 1 2 3 4 1 2 3 4 5 G023747 Figure 9 G023756 Figure 8 1. Nail (88) 4. Locknut (2) 5. Nail plate 1. Slot 3. Washer (3/8 inch) 2.
Product Overview Operation 1 Installing and Removing the Weights 2 3 8 Always ensure that your machine has the appropriate number of weights. 7 Refer to the following table for how many weights are required on the front of the machine: 6 5 4 G023749 Figure 10 1. Front weights (2 included) 5. Groomer 2. Stop-chain assembly 6. Nail drag assembly 3. Frame bracket 4. Back blade 7. Drawbar 8.
Attaching the Nail Drag to the Machine Connecting the Drawbar to the Frame Hitch 1. Align the rod end of the drawbar to the frame hitch (Figure 13). Connecting the Chains to the Attachment Lift 1 1. Position the drawbar under the machine. 2 3 2. Install a shackle on the end of each lift chain. 3. Align each shackle to the appropriate side of the attachment lift on the machine (Figure 12). A 4 4 5 G023743 Figure 13 B 1. Bolt (3/4 x 4-1/2 inches) 4. Short spacer 2. Frame hitch 3.
Connecting the Frame Bracket Removing the Nail Drag from the Machine 1. Remove the nut and the bolt securing the muffler shield to the back of the machine (Figure 14). WARNING If you drive the machine without an attachment installed, it can tip over and injure someone or damage property. Do not drive the machine without a Toro-approved attachment installed. 1. Disconnect the drawbar from the frame hitch. 2. Disconnect the shackles from the attachment lift. 3.
Adjusting the Depth Adjust the depth to suit your grooming conditions and preferences. You can also adjust the depth to compensate for worn nails. Note: If you notice that the nail drag is carrying too much material, increase the depth to allow more material to flow through the nail drag. 1. Start the machine, and raise the attachment lift so that the nail drag is up off the ground. 2. Remove the lynch pins. 3. Set the depth to suit your grooming conditions and preferences.
Maintenance Replacing the Nails 1. Start the machine, and raise the attachment lift so that the nail drag is up off the ground. 2. Remove the lynch pins from the 8 clevis pins securing the top plates to the nail plate and the bottom plate (Figure 18). Note: Retain the lynch pins for installing the top plates. 1 2 3 4 5 G023747 Figure 18 3. Remove the top plates. Note: You may need to loosen the top nuts and bolts securing the drawbar to the nail drag assembly; refer to Figure 4. 4.
Troubleshooting Problem Possible Cause Corrective Action 1. The nail depth is not correct. 1. Adjust the nail depth or remove some nails if necessary. 2. The desired appearance is not possible with the standard configuration. 3. The machine speed is too fast or too slow. 2. Install the optional drag mat kit (sold separately). 3. Adjust the machine speed, or install the optional speed limiter kit (sold separately). The nail drag contacts the tires. 1. The stop chains are not assembled properly. 1.
Notes: 13
Notes: 14
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 08717 Serial No.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
