Form No. 3391-391 Rev B Front Lift Frame Sand Pro®/Infield Pro® 5040 Traction Unit Model No. 08712—Serial No. 311000336 and Up Operator's Manual WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
Procedure 5 6 7 8 9 Description Qty. 1 2 2 2 2 2 1 1 2 2 2 Hitch frame Bolt (3/8 x 2 inches) Nut (3/8 inch) Capscrew (3/8 x 1-1/2 inches) Locknut (3/8 inch) Cylinder pin Adapter plate Push arm tube Pin assembly Thread-forming screw Bolt (5/8 x 1-1/2 inches) Washer (1.68-inch outside diameter x 0.
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Lower the attachments. 3. Engage the parking brake. 4. Shut off the engine and remove the key. g003660 Figure 1 1. Control panel 2 3. Console mounting bolt locations 2. Console Removing the Shrouds 7. Remove the 4 bolts securing the right hand wheel shroud to the frame and remove the shroud (Figure 2). No Parts Required Procedure 1.
g003663 Figure 4 1. Straight fitting 3. Lift valve 2. 90-degree fitting 2. g003662 Figure 3 1. Center shroud 3 Note: The valve installation is very similar to the valve currently installed. 3. Installing the Lift Valve Straight hydraulic fitting with O-ring 2 90-degree hydraulic fitting with O-ring 1 Lift valve 1 Valve plate 3 Bolt (1/4 x 3 inches) 3 Locknut (1/4 inch) 2 Bolt (#10 x 1-1/4 inches) 2 Locknut (#10) 1 Lift lever Procedure 1.
4. Remove and discard the 2 bolts securing the front of the steering pivot to the top of the caster fork (Figure 6). 5. Using the caster fork and steering pivot mounting holes, mount the hitch frame bracket to the underside of the caster fork with 2 bolts (1/2 x 1-3/4 inches); refer to Figure 6. Note: It may be required to partially deflate the tire to gain clearance. The wheel motor hydraulic hose should not rest on top of the hitch frame bracket. g003664 Figure 5 1. Valve assembly 4.
5 3. Insert a cylinder pin into each push arm tube as shown in Figure 8. 4. Insert the push arm tubes onto the right and left plow plates aligning the cylinder pin guides with the holes in the plow plates (Figure 8). Installing the Push Arms and Hitch Frame Note: If unable to get the push arm tubes around the plow plates, loosen the nuts securing the plow plates to the caster fork. Parts needed for this procedure: 5.
g028340 Figure 11 Important: Ensure that the existing hoses are routed above the guide, as shown in Figure 11. 6 g018349 Figure 9 1. Hitch frame bracket 2. Hitch frame 8. 3. Hitch frame tube Installing the Hydraulic Cylinder Secure the frame adapter to the hitch frame with a tube, a clevis pin, and a cotter pin (Figure 10).
7 Installing the Hydraulic Hoses Parts needed for this procedure: g003669 Figure 12 1. Hydraulic cylinder 3. 45-degree fitting 2. 90-degree fitting 4. Plug (1/8 inch) 3. 1 Tube assembly 1 Hydraulic hose (Part No. 108-8449) 1 Hydraulic hose (Part No. 108-8453) 1 Hydraulic hose (Part No.
new valve and the vacated fitting on the existing lift valve (Figure 15). 6. Connect the 45-degree fitting end of hydraulic hose, Part No. 108-8449, to the 90-degree fitting on the right side of the valve and the straight end of the hose to the vacant oil cooler fitting (Figure 15). Refer to Figure 16 and Figure 17 for hose routing. 7. Mount the wire hose holder to the left frame tube with 2 thread-forming screws (5/16 x 3/4 inch); refer to Figure 15. 8.
g218466 Figure 16 1. Cable tie 2. Hydraulic hose (Part No. 108-8449) 3. Hydraulic hose (Part No. 108-8453) 10 4. Hydraulic hose (Part No.
g218467 Figure 17 1. Cable tie 3. Hydraulic hose (Part No. 108-8453) 2. Hydraulic hose (Part No. 108-8449) 4. Hydraulic hose (Part No.
WARNING 8 Hydraulic fluid escaping under pressure can penetrate skin and cause injury. • If hydraulic fluid is injected into the skin it must be surgically removed within a few hours by a doctor familiar with this type of injury. Gangrene may result if this is not done. • Keep body and hands away from pin hole leaks or nozzles that eject high-pressure hydraulic fluid. • Use cardboard or paper to find hydraulic leaks.
Remove the hour meter from the old control panel and install it in the new control panel. Attachments/Accessories 10. Install the new control panel and plug the wire into the hour meter. 11. Secure the control panel in place with the fasteners previously removed (Figure 19). A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.
g003677 Figure 20 14
Schematics g218266 Hydraulic schematic 108-2946 (Rev.
Notes:
Notes:
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
