Installation Instructions

ManualsBrandsToro ManualsVehiclesOverhead Console Kit, Workman UTX Passenger Utility Vehicle

FormNo.3448-161RevA

OverheadConsoleKit

Workman

UTXPassengerUtilityVehicle

ModelNo.08130

InstallationInstructions

Important:IfyouareinstallingthiskitandtheWorkLightsKit(Model08131)atthesametime,install

theWorkLightsKitrst,thentheOverheadConsoleKit.

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal144-1143

144-1143

1.Warning—readtheOperator’sManual.6.Warning—donotoperatethemachineundertheinuenceof

drugsoralcohol.

2.Warning—alloperatorsshouldbetrainedbeforeoperating

themachine.

7.Fallinghazard—donotcarrypassengersinthebed;donot

carryextrapassengersinbetweentheseats.

3.Warning—wearhearingprotection.

8.Firehazard—shutofftheenginewhenaddingfueltothe

machine.

4.Collisionhazard—donotoperatethemachineonpublic

streets,roads,orhighways.

9.Warning—shiftthetransmissionlevertotheP(PARK)position,

turnthekeytotheoffposition,andremovethekeybefore

leavingthemachine.

5.Warning—donotallowpeopleundertheageof16tooperate

themachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3448-161*

Summary of content (16 pages)

PAGE 1
Form No. 3448-161 Rev A Overhead Console Kit Workman® UTX Passenger Utility Vehicle Model No. 08130 Installation Instructions Important: If you are installing this kit and the Work Lights Kit (Model 08131) at the same time, install the Work Lights Kit first, then the Overhead Console Kit. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Qty. No parts required – Console switch bracket Speed nut Thread-forming screw (1/4 x 5/8 inch) Plug Wire harness Dome light Overhead console Thread-forming screw (1/4 x 5/8 inch) Wire raceway channel Grommet 1 4 4 4 1 1 1 8 1 1 No parts required – 2 Use Prepare the machine. Install the console switch bracket. Route the wire harness and install the dome light.
PAGE 3
5. 1 Disconnect the negative (-) battery cable from the battery post. Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Shift the transmission lever to the P (PARK) position. 3. Shut off the engine and remove the key. 4. Wait for the engine to cool completely. g365494 Figure 2 1. Negative (-) battery cable g364252 Figure 1 3 2.
PAGE 4
2 Installing the Console Switch Bracket Parts needed for this procedure: 1 Console switch bracket 4 Speed nut 4 Thread-forming screw (1/4 x 5/8 inch) 4 Plug Procedure 1. Install the 4 speed nuts to the overhead console (Figure 3).
PAGE 5
2. Secure the console switch bracket to the 4 speed nuts using 4 thread-forming screws (1/4 x 5/8 inch) as shown in Figure 4. 3. Torque the 4 thread-forming screws (1/4 x 5/8 inch) to 6 N∙m (53 in-lb). g365758 Figure 4 4. Install the 4 plugs to the console switch bracket (Figure 5).
PAGE 6
3 Routing the Wire Harness and Installing the Dome Light Parts needed for this procedure: 1 Wire harness 1 Dome light Procedure 1. Install the dome light to the overhead console (Figure 6).
PAGE 7
2. Route the wire harness through the top, left opening in the overheard console as shown in Figure 7. Note: If you are not installing the Work Lights Kit, Windshield and Wiper Kit, and/or Beacon Kit, store the connectors inside the top of the overhead console. Note: Store the unused section of the wire harness near the fuse block. 3. Connect the dome light to the connectors on the wire harness (Figure 7). g365759 Figure 7 2. Route the harness starting here. 1. Connect the dome light.
PAGE 8
4 Installing the Overhead Console Parts needed for this procedure: 1 Overhead console 8 Thread-forming screw (1/4 x 5/8 inch) Procedure 1. Route the 3-pin connector and harness through the opening of the overhead console before installing the overhead console (Figure 8). g364605 Figure 8 1. Route the 3-pin connector through this opening.
PAGE 9
2. Secure the assembled overhead console to the front crosslink using 8 thread-forming screws (1/4 x 5/8 inch) as shown in Figure 9. 3. Torque the 8 thread-forming screws (1/4 x 5/8 inch) to 339 N∙cm (30 in-lb).
PAGE 10
5 Installing the Wire Raceway Channel Parts needed for this procedure: 1 Wire raceway channel 1 Grommet Procedure 1. Using the dimensions shown in Figure 10, drill a 38 mm (1-1/2 inches) diameter hole into the dash. g365495 Figure 10 1. Drill the 38 mm (1-1/2 inches) diameter hole here. 3. 33.5 mm (1-5/16 inches) 2.
PAGE 11
2. Assemble the wire harness with the 3-pin connector into the wire raceway channel (Figure 11). 3. Insert the wire harness through the slit in the grommet (Figure 11). g364606 Figure 11 1.
PAGE 12
4. Route the 3-pin connector through the hole that you drilled in step 1. 5. Install the grommet to the hole in the dash (Figure 12). 6. Adhere the wire raceway channel to the flat surface on the front, left roll bar (Figure 12).
PAGE 13
7. Raise the hood. 8. Connect the kit harness connector to the machine harness connector (Figure 13). g365922 Figure 13 1. Kit harness connector 9. 2. Machine harness connector Close the hood.
PAGE 14
6 Connecting the Battery No Parts Required Procedure Connect the negative (-) battery cable to the battery post. g365493 Figure 14 1. Negative (-) battery cable 2.
PAGE 15
Notes:
PAGE 16