Installation Instructions

ManualsBrandsToro ManualsVehiclesFolding Windshield Kit, Workman GTX Utility Vehicle with Canopy

FormNo.3428-398RevB

FoldingWindshieldKit

Workman

GTXUtilityVehiclewithCanopy

ModelNo.07923

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Foldingwindshieldassembly1

Rubberclamp2

Shortplasticrivet

Longplasticrivet8

Plasticspacer8

Installthefoldingwindshield(forcanopyModels07921

and07922).

Foldingwindshieldassembly1

Rubberclamp2

Shortplasticrivet

Longplasticrivet8

Plasticspacer8

Installthefoldingwindshield(forcanopyModels07140

and07141andcanopywithROPSModel07169).

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

g038447

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3428-398*B

Summary of content (8 pages)

PAGE 1
Form No. 3428-398 Rev B Folding Windshield Kit Workman® GTX Utility Vehicle with Canopy Model No. 07923 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Folding windshield assembly Rubber clamp Short plastic rivet Long plastic rivet Plastic spacer Folding windshield assembly Rubber clamp Short plastic rivet Long plastic rivet Plastic spacer 1 2 2 8 8 1 2 2 8 8 Prepare the machine.
PAGE 2
Installing the Folding Windshield For Canopy Models 07921 and 07922 1. Unfold the windshield and secure the upper portion of the windshield to the canopy support tubes using the 2 rubber clamps and 2 short plastic rivets in the upper holes (Figure 2). g275466 Figure 3 3. Windshield—upper portion 2. Rubber clamp 4. Canopy support tube 2. Align the holes in lower portion of the windshield with the holes in the canopy support tubes (Figure 3). 3.
PAGE 3
5. Installing the Folding Windshield Secure the bottom of the lower portion of the windshield to the dash using 2 plastic spacers and 2 long plastic rivets (Figure 5). Note: Ensure that you install the plastic spacers For Canopy Models 07140 and 07141 and Canopy with ROPS Model 07169 between the windshield and dash. 1. Mark and drill 3 holes (8 mm or 5/16 inch) in each canopy support tube using the measurements shown in Figure 6.
PAGE 4
g276799 Figure 6 Driver’s side tube shown 4
PAGE 5
2. Unfold the windshield and secure the upper portion of the windshield to the canopy support tubes using the 2 rubber clamps and 2 short plastic rivets in the lower holes (Figure 7). 5. Using the windshield as the template, drill 2 holes (8 mm or 5/16 inch) into the dash (Figure 9). g276757 Figure 7 1. Short plastic rivet 3. Windshield—upper portion 2. Rubber clamp 4. Canopy support tube 3. 4.
PAGE 6
Operation Maintenance Transporting a Machine with the Windshield Installed Cleaning the Windshield 1. Rinse the windshield with lukewarm water (60° C or 140° F). 2. Using a soft cloth or sponge, wash the windshield with mild-detergent soap to clear the dirt and grime. When transporting a machine with the folded windshield installed, ensure that you follow these recommendations: Important: Do not scrub the windshield with • The machine is facing forward during a brush or rough fiber.
PAGE 7
Notes:
PAGE 8