Installation Instructions

ManualsBrandsToro ManualsVehiclesWindshield and Wiper Kit, Workman GTX Utility Vehicle

FormNo.3421-874RevB

WindshieldandWiperKit

Workman

GTXUtilityVehicle

ModelNo.07407

InstallationInstructions

YoumustinstalltheCanopyKit(ModelNo.07140

forthe2-passengerGTXmachineorModelNo

07141forthe4-passengerGTXmachine)priorto

installingthiskit.

Ifyouhavea2017andolderCanopyKit(ModelNo.

07140forthe2-passengerGTXmachineorModel

No07141forthe4-passengerGTXmachine),you

needtoorderthefollowingpartsforinstallation:

•Rightmountbracket—ToroPartNo.

136-9389-03

•Leftmountbracket—ToroPartNo.136-9392-03

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal137-1438

137-1438

1.Windshieldwasher—On2.Windshieldwiper—Off

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3421-874*B

Summary of content (16 pages)

PAGE 1
Form No. 3421-874 Rev B Windshield and Wiper Kit Workman® GTX Utility Vehicle Model No. 07407 Installation Instructions You must install the Canopy Kit (Model No. 07140 for the 2-passenger GTX machine or Model No 07141 for the 4-passenger GTX machine) prior to installing this kit. If you have a 2017 and older Canopy Kit (Model No.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 Description Qty. Use No parts required – Prepare the machine. No parts required – Disconnect the battery. Grommet 1 Install the grommet to the dashboard.
PAGE 3
1 3 Preparing the Machine Installing the Grommet No Parts Required Parts needed for this procedure: 1 Grommet Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Open the hood; refer to your machine Operator’s Manual. Procedure 1. Place the grommet on the inner side of the right dashboard depression as shown in Figure 1.
PAGE 4
Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 2 Cable tie For Electric Machines Important: The Power Converter Kit is required to use the Windshield and Wiper Kit on a Workman GTX Electric utility vehicle. Contact your authorized Toro dealer for more information. Use the following instructions and illustrations to route and connect the wire harness. Refer to Figure 2 for an overview of the wire harness position.
PAGE 5
1. Route the wire harness along the floor-channel plate and through the opening in the frame channel (Figure 3). g036334 Figure 3 1. Frame channel 3. Floor-channel plate 2. Kit wire harness 2. Route the wire harness through the opening in the top of the frame channel (Figure 4). g036335 Figure 4 1. Frame channel 3. 2. Kit wire harness Pass the 6-socket connector of the wire harness through the grommet in the dashboard (Figure 5). Use a cable tie to secure the wire harness to the machine.
PAGE 6
4. Route the 8-socket connector of the wire harness toward the left side of the dash (Figure 5). Use a cable tie to secure the wire harness to the machine. Note: The 8-socket connector is installed in 5 Installing the Switch (page 8). 5. Install the black ground wire to the ground wire on the Power Converter Kit wire harness (Figure 6). Note: The black terminal ring is not used. 6. Install the red power wire to the power wire on the Power Converter Kit wire harness (Figure 6). g194797 Figure 6 1.
PAGE 7
For Gasoline Machines Use the following instructions and illustrations to route and connect the wire harness. Refer to Figure 2 for an overview of the wire harness position. Note: The wire harness length allows for installation on a 4-passenger GTX machine. For 2-passenger GTX machines, coil the wire harness in the frame channel as shown in Figure 2. 1. Route the wire harness along the floor-channel plate and through the opening in the frame channel (Figure 3). 2.
PAGE 8
5 Installing the Switch Parts needed for this procedure: 1 Rocker switch 1 Decal Procedure Refer to Figure 9 for this procedure. 1. Locate the plug that is adjacent to the hour meter on the dashboard 2. Remove the plug from the opening. 3. Pull the 8-socket connector of the wire harness through the opening in the dashboard. 4. Connect the 8-pin connector of the rocker switch into the 8-socket connector of the wire harness.
PAGE 9
Procedure 1. Apply the 3 rubber pads to the motor mount bracket using the measurements shown in Figure 10. g225227 Figure 10 1. 14.1 cm (5-9/16 inches) 3. 12.7 mm (1/2 inch) 2. 12.7 mm (1/2 inch) 4. 2.54 cm (1 inch) 2. Use 2 flange-head screws (1/4 x 1-1/2 inches) and 2 flange nuts (1/4 inch) to secure the mount bracket to the windshield support (Figure 11). g225228 Figure 11 1. Flange nut (1/4 inch) 4. Flange-head screw (1/4 x 1-1/2 inches) 2. Motor mount bracket 5. Rubber pad 3.
PAGE 10
3. Remove the hardware from the motor as shown in Figure 12. g225941 Figure 12 1. Acorn nut 6. Cover cup (M16) 2. Cover cup (M8) 7. Washer seal (M16) 3. Washer seal (M8) 8. Mount bracket 4. Wiper stud nut 5. Nut (M16) 4. 9. Stud cover 10. Lock washer Use the hardware shown in Figure 12 to secure the motor to the mount bracket. Note: Set aside the lock washer and wiper stud nut for use in 10 Installing the Wiper (page 14) 5.
PAGE 11
2. 7 For installation on machines equipped with Model 07921 or 07922 canopies only: In the top hole of the canopy tubes, install the windshield mounting brackets (Figure 14). Installing the Windshield Support Parts needed for this procedure: 4 Flange-head screw (1/4 x 1-1/2 inches) 4 Flange nut (1/4 inch) 2 Windshield mount bracket 2 Hex-head screw (5/16 x 3/4 inch) 4 Phillips-head screw 4 Speed nut g265330 Procedure 1. Figure 14 1.
PAGE 12
4. Use 4 Phillips-head screws and 4 speed nuts to secure the mount bracket cover to the mount bracket (Figure 16). g218174 Figure 16 1. Speed nut 3. Mount bracket cover 2.
PAGE 13
8 Installing the Windshield Parts needed for this procedure: 1 Windshield 4 Shoulder screw (5/16 x 1-1/4 inches) 4 Backup washer 8 Flange bushing 4 Flange nut (5/16 inch) 2 Bumper Procedure Use 4 shoulder screws (5/16 x 1-1/4 inches), 4 backup washers, 8 flange bushings, 4 flange nuts (5/16 inch), and 2 bumpers to install the windshield to the windshield supports (Figure 17). g265613 Figure 17 Model 07140 and 07141 canopies shown 1. Shoulder screw (5/16 x 1-1/4 inches) 4. Windshield 2.
PAGE 14
9 Connecting the Battery No Parts Required For Gasoline GTX Vehicles Connect the negative battery cable; refer to your machine Operator’s Manual. g218248 Figure 18 For Electric GTX Vehicles 1. Wiper stud nut 3. Wiper arm 2. Lock washer Connect the main negative battery cable (black) that connects the bank of batteries to the ground point of the machine; refer to your machine Operator’s Manual. 4. Position the arm using the measurements shown in Figure 19.
PAGE 15
Operation Using the Wipers Press the rocker switch to turn the wipers to the ON or OFF position; refer to Figure 20. g217763 Figure 20 1. ON position 2. OFF position Using the Wiper Fluid Refer to the Windshield Wiper Kit Installation Instructions for wiper fluid operation.
PAGE 16