Installation Instructions

ManualsBrandsToro ManualsVehiclesCab Kit, Workman MD/MDE/MDX/MDXD Utility Vehicle

FormNo.3389-927RevB

CabKit

Workman

MD/MDE/MDX/MDXDUtilityVehicle

ModelNo.07320—SerialNo.315000001andUp

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal93-9850

93-9850

1.Donotrepairorrevise—readtheOperator'sManual.

decal117-4955

117-4955

1.Warning—readtheOperator'sManual;weartheseatbelt

whenseatedintheoperator'sposition;avoidtippingthe

machine.

2.Warning—wearhearingprotection.

decal130-5964

130-5964

1.Warning—intheeventofanemergency1)Pullthelocking

pinoutofeachhinge;2)Pushthefrontwindowouttoexit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3389-927*B

Summary of content (12 pages)

PAGE 1
Form No. 3389-927 Rev B Cab Kit Workman® MD/MDE/MDX/MDXD Utility Vehicle Model No. 07320—Serial No. 315000001 and Up Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
PAGE 2
decal130-5439 130-5439 1. Read the Operator’s Manual for information on fuses. 4. Windshield spray 2. Windshield wiper (15 A) 5. Windshield wiper 3.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the ROPS assembly. Compression spring 2 Install the compression spring.
PAGE 4
1 3 Preparing the Machine Installing the Compression Spring No Parts Required Parts needed for this procedure: Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Raise the bed until the prop rod is fully engaged; refer to the Operator’s Manual. 4. Shut off the engine and remove the key. 5. Disconnect the battery; refer to the Operator’s Manual. 2 Compression spring Procedure Important: For 2015 and older models, you must order the 2 compression springs (Toro Part No.
PAGE 5
4 5 Installing the Floor Mounts Installing the Cab Frame Parts needed for this procedure: Parts needed for this procedure: 2 Floor mount 1 Cab frame 6 Nut (3/8 inch) 4 Bolts (3/8 x 7/8 inch) 4 Bolt (3/8 x 1 inch) 10 Bolt (3/8 x 3/4 inch) 2 Bolt (5/16 inch) 10 Nuts (3/8 inch) 2 Nut (5/16 inch) 2 Bolt (3/8 x 7/8 inch) 2 Washer Procedure Lift the cab frame using the lifting points and place it on the machine (Figure 4). Procedure 1.
PAGE 6
7 Installing the Side Panels Installing the Seat Belts Parts needed for this procedure: Parts needed for this procedure: 2 Side-plate panels 2 Seat-belt anchors 4 Bolts (1/4 inch) 4 Bolts (3/8 x 3/4 inch) 2 Side-plate foam panel 4 Nuts (3/8 inch) 2 Seat belt receiver end 4 Bolt (7/16 inch) 4 Nut (7/16 inch) 2 Seat-belt bracket 2 Seat belts 2 Bolt (3/8 x 7/8 inch) Installing the Side-Plate Panels 1.
PAGE 7
5. Secure the left and right seat belt anchor to the front frame with 4 bolts (3/8 x 3/4 inch) and 4 nuts (3/8 inch) as shown in Figure 8. g026314 Figure 10 9. Mount the receiver end of each seat belt assembly to each seat belt anchor with a bolt (7/16 inch) and nut (7/16 inch) as shown in Figure 10. g026308 Figure 8 10. Torque the bolts to 67 to 83 N∙m (49 to 61 ft-lb). 6. Torque the 4 bolts (3/8 x 3/4 inch) to 37 to 45 N∙m (27 to 33 ft-lb). 7.
PAGE 8
Connect the ring terminal on the harness to the grounding block and insert the fuse block connector into an available fuse block connection (Figure 12). If a fuse block connection is not available, add a fuse block to the fuse block grouping. Contact your Authorized Service Dealer for more information. 8 Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 1 Clip tie 1 Plug 1 Fuse (30 A) Procedure There are 2 options for routing the wire harness.
PAGE 9
Product Overview Controls Control Panel Windshield Wiper Switch Push the top of the switch to activate the windshield wipers (Figure 13). g026274 Figure 13 1. Windshield wiper control 2. Light switch Light Switch Push the light plate to turn on the light (Figure 13). Windshield Latch Lift up on latches to open the windshield (Figure 14). Press in the latch to lock the windshield in the OPEN position. Pull out and down on the latch to close and secure the windshield. g026672 g026672 Figure 14 1.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12
Declaration of Incorporation Model No. 07320 Serial No. Product Description Invoice Description General Description Directive 315000001 and Up Cab Kit, Workman MD/MDE/MDX/MDXD Utility Vehicle CAB-MID DUTY WORKMAN Utility Vehicle 2006/42/EC, 2000/14/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC. We will undertake to transmit, in response to requests by national authorities, relevant information on this partly completed machinery.