Installation Instructions

ManualsBrandsToro ManualsVehiclesCab Kit, Workman MD/MDE/MDX/MDXD Utility Vehicle

FormNo.3408-281RevA

CabKit

Workman

MD/MDE/MDX/MDXDUtilityVehicle

ModelNo.07320—SerialNo.400000000andUp

InstallationInstructions

Important:For2016andnewermachines,youmust

installtheheavy-dutyspringsthataresuppliedwith

theCabKitinordertousethecabonaWorkman

MD/MDE/MDX/MDXDutilityvehicle.

For2015andoldermachines,discardthesprings

includedinthiskitandorder2springs(ToroPartNo.

117-4847)fromyourAuthorizedToroDealer.

ThespringsshouldbeinstalledonlybyqualiedToro

ServiceTechniciansusingapprovedtools.Improper

removal,disassembly,orinstallationofthespring

assemblyposesadangertoyouandbystanders.Please

contactyourAuthorizedToroDealerfortheappropriate

toolsandproperinstallationofthiskit.

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedormissing.

decal93-9850

93-9850

1.Donotrepairorrevise—readtheOperator'sManual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3408-281*A

Summary of content (16 pages)

PAGE 1
Form No. 3408-281 Rev A Cab Kit Workman® MD/MDE/MDX/MDXD Utility Vehicle Model No. 07320—Serial No. 400000000 and Up Installation Instructions Important: For 2016 and newer machines, you must install the heavy-duty springs that are supplied with the Cab Kit in order to use the cab on a Workman MD/MDE/MDX/MDXD utility vehicle. For 2015 and older machines, discard the springs included in this kit and order 2 springs (Toro Part No. 117-4847) from your Authorized Toro Dealer.
PAGE 2
decal130-5964 130-5964 1. Warning—in the event of an emergency 1) Pull the locking pin out of each hinge; 2) Push the front window out to exit. decal117-4955 117-4955 1. Warning—read the Operator's Manual; wear the seat belt when seated in the operator's position; avoid tipping the machine. 2. Warning—wear hearing protection. decal130-5439 130-5439 1. Read the Operator’s Manual for information on fuses. 4. Windshield spray 2. Windshield wiper (15 A) 5. Windshield wiper 3.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 2 No parts required – Prepare the machine. No parts required – Remove the strut assembly (for 2016 and newer machines only). 3 Spring 2 Install the springs (for 2016 and newer machines only). 4 No parts required – Install the strut assembly (for 2016 and newer machines only). 5 6 Compression spring 2 Install the compression spring (for 2015 and older machines only).
PAGE 4
Procedure Description Qty. 11 Wire harness Clip tie Plug Fuse (30 A) Ground block (MDE machines only) Jumper strip (MDE machines only) Bolt (#10 x 3/4 inch, MDE machines only) Nut (#10, MDE machines only) Ground-adapter harness (MDE machines only) Power-adapter harness (MDE machines only) 1 1 1 1 1 1 2 Use Route the wire harness. 2 1 1 Media and Additional Parts Description 12 V Power Plug Adapter Kit Use Qty. This kit is needed for the Workman MDE Utility Vehicle only.
PAGE 5
2 Removing the Strut Assembly (for 2016 and Newer Machines Only) No Parts Required Procedure 1. Remove the front wheel. 2. Remove the hex-head bolt (3/8 x 4-3/4 inches) and flange nut (3/8 inch) from the spindle (Figure 1). 3. Remove the hex-head bolt (3/8 x 3-1/2 inches) and flange nut (3/8 inch) from the control arm (Figure 1). 4. Remove the hex-head bolt (1/2 x 2-1/4 inches) and locknut (1/2 inch) securing the strut assembly to the upper frame (Figure 1). 5. Remove the strut assembly (Figure 1).
PAGE 6
3. Torque the hex-head bolt (1/2 x 2-1/4 inches) to 91 to 113 N∙m (67 to 83 ft-lb). 3 4. Install the hex-head bolt (3/8 x 4-3/4 inches) and flange nut (3/8 inch) to the spindle (Figure 1). Installing the Springs (for 2016 and Newer Machines Only) 5. Torque the hex-head bolt (3/8 x 4-3/4 inches) to 37 to 45 N∙m (27 to 33 ft-lb). 6. Secure the lower portion of the strut assembly to the control arm using the hex-head bolt (3/8 x 3-1/2 inches) and flange nut (3/8 inch) as shown in Figure 1. 7.
PAGE 7
3. Using a spring compressor, remove the current springs and install the springs from this kit. 7 4. Install the shock assemblies and turn them 3 clicks up from the longest position. Installing the Floor Mounts Note: Refer to the Service Manual for further instructions on replacing the spring and checking the front end toe of the tires. Parts needed for this procedure: 5. Torque the bolts to 95 to 122 N∙m (70 to 90 ft-lb).
PAGE 8
9 Installing the Cab Frame Installing the Side Panels Parts needed for this procedure: Parts needed for this procedure: 1 Cab frame 2 Side-plate panels 4 Bolts (3/8 x 7/8 inch) 4 Bolts (1/4 inch) 10 Bolt (3/8 x 3/4 inch) 2 Side-plate foam panel 10 Nuts (3/8 inch) Procedure Procedure 1. Fasten the mounting plates onto the cab using 4 bolts (1/4 inch) as shown in Figure 7. 1. Lift the cab frame using the lifting points and place it on the machine (Figure 5). 2.
PAGE 9
10 Installing the Seat Belts Parts needed for this procedure: 2 Seat-belt anchor 4 Bolts (3/8 x 3/4 inch) 4 Nuts (3/8 inch) 2 Seat-belt receiver end 4 Bolt (7/16 inch) 4 Nut (7/16 inch) 2 Seat-belt bracket 2 Seat belt 2 Bolt (3/8 x 7/8 inch) g026308 Figure 9 6. Torque the 4 bolts (3/8 x 3/4 inch) to 37 to 45 N∙m (27 to 33 ft-lb). Procedure 7. Using the dimensions shown in Figure 10, locate, mark, and drill 2 holes in the top of the seat shroud. 1.
PAGE 10
• Route the wire harness under the control panel (Box A of Figure 12). Install the clip tie in the lower hole on the side panel and the plug in the top hole. • Drill a hole into the console, install the clip tie in the top hole on the side panel, and install the plug into the lower hole (Box B of Figure 12). Important: Use caution when drilling this hole; electrical components and control cables are located under the seat shroud. A g026314 Figure 11 9.
PAGE 11
g035781 Figure 15 g027556 Figure 13 1. Ground block 2. Wire harness 1. Wire harness ring terminal 4. Power-adapter harness 2. Ground-adapter harness 5. Wire harness from the 12 V Plug Adapter Kit 3. Wire harness 3. Fuse block D. 3. For Workman MDE machines, complete as follows: E. Connect the power-adapter harness and the ground-adapter harness to the wire harness from the 12 V Plug Adapter Kit. Note: The 12 V Plug Adapter Kit (sold separately) must be installed on the machine. 4.
PAGE 12
Product Overview Controls Control Panel Windshield-Wiper Switch Push the top of the switch to activate the windshield wipers (Figure 16). g026274 Figure 16 1. Windshield-wiper switch 2. Light switch Light Switch Push the light plate to turn on the light (Figure 16). Windshield Latch Lift up the latches to open the windshield (Figure 17). Press in the latch to lock the windshield in the open position. Pull out and down on the latch to close and secure the windshield. g026672 g026672 Figure 17 1.
PAGE 13
Notes:
PAGE 14
Declaration of Incorporation Model No. 07320 Serial No. Product Description Invoice Description General Description Directive 400000000 and Up Cab Kit, Workman MD/MDE/MDX/MDXD Utility Vehicle CAB-MID DUTY WORKMAN Utility Vehicle 2006/42/EC, 2004/108/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC. We will undertake to transmit, in response to requests by national authorities, relevant information on this partly completed machinery.
PAGE 15
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
PAGE 16
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).