Installation Instructions

ManualsBrandsToro ManualsVehiclesCanopy Mount Kit, Workman GTX Utility Vehicle with Extended Flatbed

FormNo.3433-807RevA

CanopyMountKit

Workman

GTXUtilityVehiclewithExtendedFlatbed

ModelNo.07199

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheexistingseatbasepanel

andseatsupportchannels.

Canopyadaptermountbracket

Seatbasepanel

Flange-headbolt(1/4x5/8inch)

Locknut(1/4inch)

Installthecanopyadaptermount

bracketsandnewseatbasepanel.

Canopyadapterbracket

Carriagebolt(5/16x3/4inch)

Flangenut(5/16inch)

Flange-headbolt(3/8x1-3/4inches)

Locknut(3/8inch)

Installthecanopyadapterbrackets.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

g038447

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3433-807*A

Summary of content (12 pages)

PAGE 1
Form No. 3433-807 Rev A Canopy Mount Kit Workman® GTX Utility Vehicle with Extended Flatbed Model No. 07199 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the existing seat base panel and seat support channels.
PAGE 2
Removing the Seat Base Panel and Support Channels No Parts Required Procedure 1. Remove the seat assembly; refer to the Operator’s Manual. 2. Remove the 2 torx-head screws securing the seat base side panels from each side (Figure 2). g296241 Figure 2 3. Remove the hex-head bolt, washer, and flange nut securing the floorboard bracket to the floorboard, seat base side panels, and rear seat base panel from each side (Figure 2). 4.
PAGE 3
5. Remove the 2 hex head bolts securing the floor panel to the frame (Figure 4). g295648 Figure 4 6. Rotate the side panels out for accessibility (Figure 5).
PAGE 4
3 Installing the Canopy Adapter Mount Brackets and New Seat Base Panel Parts needed for this procedure: 2 Canopy adapter mount bracket 1 Seat base panel 4 Flange-head bolt (1/4 x 5/8 inch) 4 Locknut (1/4 inch) Procedure 1. Secure the canopy adapter mount brackets to the machine using existing hardware (Figure 6).
PAGE 5
2. Mark and drill 4 (size) holes as shown in Figure 7 and Figure 8.
PAGE 6
3. Secure the canopy adapter mount brackets to the upper bracket using 4 flange-head bolts (1/4 x 5/8 inch) and 4 locknuts (1/4 inch) as shown in Figure 9. g295680 Figure 9 4. Install the seat base panel (Figure 10).
PAGE 7
5. Install the machine hardware removed in 2 Removing the Seat Base Panel and Support Channels (page 1); Figure 11 to Figure 13.
PAGE 8
g296241 Figure 13 4 Installing the Canopy Adapter Brackets Parts needed for this procedure: 2 Canopy adapter bracket 4 Carriage bolt (5/16 x 3/4 inch) 4 Flange nut (5/16 inch) 4 Flange-head bolt (3/8 x 1-3/4 inches) 4 Locknut (3/8 inch) Procedure 1. Secure the canopy adapter brackets using 4 carriage bolts (5/16 x 3/4 inch) and 4 flange nuts (5/16 inch) as shown in Figure 14.
PAGE 9
g295644 Figure 14 2. Install and secure the canopy tubes to the canopy adapter brackets using 4 flange-head bolts (3/8 x 1-3/4 inches) and 4 locknuts (3/8 inch) as shown in Figure 15.
PAGE 10
g295645 Figure 15 3. Install the seat assembly; refer to the Operator’s Manual.
PAGE 11
Notes:
PAGE 12