Installation Instructions

ManualsBrandsToro ManualsVehicles2in L-Track Kit, Workman GTX Utility Vehicle

FormNo.3426-310RevA

2inor6inL-TrackKit

Workman

GTXUtilityVehicle

ModelNo.07158

ModelNo.07159

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

15.2cm(6inches)L-Trackbracket

Ringassembly4

Screw(nethread)

Screw(coarsethread)

Installa15.2cm(6inches)L-Trackbracket.

5cm(2inches)L-Trackbracket

Ringassembly4

Screw(coarsethread)

Installa5cm(2inches)L-Trackbracket(foraplastic

cargobed).

5cm(2inches)L-Trackbracket

Ringassembly4

Screw(nethread)

Locknut(1/4inch)

Installa5cm(2inches)L-Trackbracket(fora1.8M(6ft)

atbedwithTubeSidesKit).

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

g038447

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3426-310*A

Summary of content (4 pages)

PAGE 1
Form No. 3426-310 Rev A 2in or 6in L-Track Kit Workman® GTX Utility Vehicle Model No. 07158 Model No. 07159 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – 15.
PAGE 2
Installing a 15.2 cm (6 inches) L-Track Bracket 1. 2. Install and use the ring assembly as shown in Figure 4. Attach the bracket in the locations shown in Figure 2 using 2 screws (Figure 3). g034230 Figure 4 15.2 cm (6 inches) L-Track bracket shown g034228 Figure 2 1. Possible bracket locations 1. Correct position 2. Front of the bed g034229 Figure 3 1. Coarse-threaded screws—2.03 to 2.50 N∙m (18 to 22 in-lb) 4. Side of the bed 2. Bracket 5. Fine-threaded screws—4.52 to 5.
PAGE 3
Installing a 5 cm (2 inches) L-Track Bracket 2. For a Plastic Cargo Bed 1. Attach the bracket in the locations shown in Figure 5 using 2 screws (Figure 6). g034231 Figure 5 1. Possible bracket locations g034357 Figure 6 1. Coarse-threaded screws—2.03 to 2.50 N∙m (18 to 22 in-lb) 3. Bed 2. Bracket 3 Install and use the ring assembly as shown in Figure 4.
PAGE 4
Installing a 5 cm (2 inches) L-Track Bracket For a 1.8 M (6 ft) Flat Bed with Tube Sides Kit 1. Attach the bracket in the locations shown in Figure 7 using 2 screws (Figure 8). g268405 Figure 7 1. Possible bracket locations g268406 Figure 8 1. Fine-threaded screws—5.2 to 6.8 N∙m (46 to 60 in-lb) 3. Locknut (1/4 inch) 2. Bracket 2. Install and use the ring assembly using 2 fine-threaded screws and locknuts (1/4 inch) as shown in Figure 4.