Installation Instructions

ManualsBrandsToro ManualsVehiclesExtended 6-ft/1.8M Flat Bed Kit, Workman GTX Series Utility Vehicle

FormNo.3407-645RevB

ExtendedBedKit

Workman

GTXSeriesUtilityVehicle

ModelNo.07149

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Important:Youmustinstalla12VElectricLiftKit(ToroModelNo.07167)or48VElectricLiftKit(ToroModel

No.07168)inordertolifttheextendedcargobed.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheplasticcargobed.

Extendedcargobed1

Bed-supportbracket2

Self-tappingscrew(5/16x3/4inch)

Flange-headscrew(1/2x4-1/2inches)

Locknut(1/2inch)

Thandle1

Installtheextendedcargobed.

Nopartsrequired

–

Installstakesidestotheextendedatbed(optional).

PreparingtheMachine

1.Movethemachinetoalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekeyfromthekeyswitch..

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-645*B

Summary of content (8 pages)

PAGE 1
Form No. 3407-645 Rev B Extended Bed Kit Workman® GTX Series Utility Vehicle Model No. 07149 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Important: You must install a 12 V Electric Lift Kit (Toro Model No. 07167) or 48 V Electric Lift Kit (Toro Model No. 07168) in order to lift the extended cargo bed.
PAGE 2
Removing the Plastic Cargo Bed 4. Using an overhead hoist, lower the cargo bed. 5. Remove the 2 pivot bolts (1/2 x 4-1/2 inches) and 2 locknuts (1/2 inch) from the pivot bracket located at the rear of the machine (Figure 4). 1. Using an overhead hoist, raise the plastic cargo bed. 2. Remove the 3 flange-head screws (5/16 x 3/4 inch) and prop rod U bracket from the prop rod (Figure 2). Note: Retain the hardware if you want to install the plastic cargo bed in the future.
PAGE 3
Installing the Extended Cargo Bed 3. Install the 2 bed-support brackets to the seat supports using 4 self-tapping screws (5/16 x 3/4 inch) as shown in Figure 7. 1. If there are existing rear seats, remove them (Figure 5). Figure 7 Passenger Side Shown Figure 5 3. Bed-support bracket 1. Seat support 2. Self-tapping screw (5/16 x 3/4 inch) 2. Remove the 2 screws (5/16 x 3/4 inch) and 2 flange nuts (5/16 inch) from each armrest, and remove the rear armrests (Figure 6). 4.
PAGE 4
7. Install the T handle onto the button-head screw (Figure 9). Figure 9 1. Button-head screw 2. T handle 8. Tighten the jam nut (3/8 inch) fully against the T handle (Figure 10). Figure 10 1. Jam nut (3/8 inch) 2. T handle 9. Install the Electric Lift Kit; refer to the Installation Instructions.
PAGE 5
Installing Stake Sides Optional To install the optional stake sides, you need the following measurements and quantities of wood: Wood Dimensions Total Length of Each Board Quantity Needed 38 x 89 mm (2 x 4 inch) 36 cm (14 inches) when installing without a cab, 31 cm (12 inches) when installing with a cab 8 29 x 140 mm (5/4 x 6 inch) 117 cm (46 inches) 4 29 x 140 mm (5/4 x 6 inch) 180 cm (71 inches) 4 You also need the following hardware: Hardware Use Quantity Needed Button-head bolt (5/16-18
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8
Declaration of Incorporation Model No. 07149 Serial No. Product Description Invoice Description None and Up Extended Bed Kit, Workman GTX Series Utility Vehicle EXTENDED BED KIT [WORKMAN] General Description Directive Utility Vehicle 2006/42/EC, 2004/108/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC. We will undertake to transmit, in response to requests by national authorities, relevant information on this partly completed machinery.