Installation Instructions

ManualsBrandsToro ManualsVehiclesBrush Guard Kit, Workman GTX or MDX Series Utility Vehicles

FormNo.3437-482RevA

BrushGuardKit

Workman

GTXorMDXSeriesUtilityVehicles

ModelNo.07145

InstallationInstructions

Important:YoucannotuseorinstalltheBallCageKit(ModelNo.07161)withthiskit.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Longmount-bracketassembly1

Nut(5/16inch)

Brushguard1

Carriagebolt

Bolt(5/16x3/4inch)

Installthebrushguard(forGTXmodels).

Shortupperbrush-guardbracket

Carriagebolt(5/16x7/8inch)

Nut(5/16inch)

Brushguard1

Lowerbrush-guardbracket1

Bolt(5/16x3/4inch)

Bolt(3/8x1inch)

Nut(3/8inch)

Installthebrushguard(forMDXmodels).

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

g038447

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3437-482*A

Summary of content (4 pages)

PAGE 1
Form No. 3437-482 Rev A Brush Guard Kit Workman® GTX or MDX Series Utility Vehicles Model No. 07145 Installation Instructions Important: You cannot use or install the Ball Cage Kit (Model No. 07161) with this kit. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
Installing the Brush Guard 6. For GTX Models Secure the brush guard to the bumper-mount bracket using 4 bolts (5/16 x 3/4 inch) and 4 nuts (5/16 inch) as shown in Figure 4 and Figure 5. Note: Install all fasteners loosely. 1. Install the long mount-bracket assembly through the bumper (Figure 2). g033820 Figure 4 1. Bolt (5/16 x 3/4 inch) 3. Bumper-mount bracket 2. Brush guard g033818 Figure 2 1. Long mount-bracket assembly 3. Nut (5/16 inch) 2. Bumper-mount bracket 2. Open the hood. 3.
PAGE 3
Installing the Brush Guard 6. For MDX Models Install the lower brush-guard bracket to the bumper-support bracket using 4 bolts (3/8 x 1 inch) and 4 nuts (3/8 inch) as shown in Figure 8 and Figure 9. Note: Install all fasteners loosely. 1. Install the short upper brush-guard bracket through the bumper (Figure 6. g033822 Figure 6 1. Short upper brush-guard bracket 2. Bumper-support bracket 3. Nut (5/16 inch) g033890 Figure 8 2. Open the hood. 3.
PAGE 4
7. Install the brush guard to the short upper brush-guard bracket using 2 carriage bolts and 2 nuts (5/16 inch) as shown in Figure 10. g033819 Figure 10 1. Carriage bolt 4. Carriage bolt 2. Short upper brush-guard bracket 3. Brush guard 5. Nut (5/16 inch) 8. Torque the fasteners securing the lower brush-guard bracket to the bumper-support bracket to 37 to 45 N∙m (27 to 33 ft-lb). 9. Torque all remaining fasteners to 198 to 254 N∙cm (175 to 225 in-lb).