Addendum

ManualsBrandsToro ManualsVehiclesCab Kit, Workman GTX Utility Vehicle

FormNo.3434-943RevA

CabKit

Workman

GTXUtilityVehicle

ModelNo.07142

Addendum

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Hex-washerheadscrew(#10x3/4inch)—for

electricmachineswithSerialNo.403448001

andaboveonly

2Routethewireharness.

Cabadapterwireharness—forelectric

machineswithSerialNo.403448001and

belowonly.

1Installthecabadapterwireharness.

TheincludedwireharnessandhardwareisforelectricmachineswithSerialNo.403448001andabove,orany

machinethathashadtheignitionswitchupdatekitandcabkitaddedtoit.

PreparingtheMachine

1.Parkthemachineonalevelsurface,setthe

parkingbrake,shutofftheengine,andremove

thekey.

2.Raisethebeduntilthebedproprodisfully

engaged;refertotheOperator’sManualforthe

machine.

3.Removetheseatbase.

4.Disconnectthenegativebatterycable;referto

yourOperator’sManual.

RoutingtheWireHarness

ForElectricMachines

Important:ThePowerConverterKitisrequired

tousethecabonaWorkmanGTXElectricutility

vehicle.Contactyourauthorizedthemanufacturer

distributorformoreinformation.

1.FormachineswithSerialNo.403448001and

above,securethenewfuseblockusingthe2

hex-washerheadscrews(#10x3/4inch)and2

serratednuts(#10)asshowninFigure1.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3434-943*A

Summary of content (4 pages)

PAGE 1
Form No. 3434-943 Rev A Cab Kit Workman® GTX Utility Vehicle Model No. 07142 Addendum Setup Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine. Hex-washer head screw (#10 x 3/4 inch)—for electric machines with Serial No. 403448001 and above only 2 Route the wire harness. Cab adapter wire harness—for electric machines with Serial No. 403448001 and below only. 1 Install the cab adapter wire harness.
PAGE 2
5. Install the black ground wire to the ground wire on the Power Converter Kit wire harness (Figure 3). Note: The black terminal ring is not used. 6. Install the red power wire to the power wire on the Power Converter Kit wire harness (Figure 3). g290937 Figure 1 1. New fuse block 3. Serrated nut (#10) 2. Hex-washer head screw (#10 x 3/4 inch) 4. Female connector g278776 2. For machines with Serial No.
PAGE 3
8. Lower the bed and connect the battery; refer to the Operator’s Manual. 9. Install the previously removed seat base. Installing the Cab Adapter Wire Harness Electric Machines Only For machines with Serial No. 403448001 and below, install the cab adapter wire harness as follows: 1. Open the hood; refer to your machine Operator’s Manual. 2. Disconnect the 4-pin plug on the main harness from the DC converter under the dash. g299566 Figure 6 1. 4-pin socket on the cab adapter wire harness. 4. 2.
PAGE 4
6. Connect the loose square socket on the power converter wire harness to the cab adapter wire harness (Figure 8). g299581 Figure 8 1. Power converter harness connections to the cab adapter harness. 7. Secure the hood; refer to your machine Operator’s Manual.