Form No. 3406-313 Rev B Canopy Kit Workman® GTX Utility Vehicle Model No. 07140—Serial No. 316000501 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3.
Installing the Kit Parts needed for this procedure: 1 Left loop bracket 1 Right loop bracket 2 Tube 1 Left windshield support 1 Right windshield support 1 Left, rear plate 1 Right, rear plate 1 Left, front plate 1 Right, front plate 1 Left corner gusset 1 Right corner gusset 1 Rear crosslink 1 Front crosslink 2 Backing plate 2 Crosslink tube 38 Flange nut (5/16 inch) 4 Flange nut (1/4 inch) 20 Carriage bolt (5/16 x 1-3/4 inches) 4 Hex-flange bolt (3/8 x 1 inch) 4 Fla
Procedure Note: Do not tighten any fasteners except when instructed. 1. Install the left loop bracket as follows: A. Remove the rivet from left panel behind the rear seat base (Figure 1). B. Install the left loop bracket using 2 hex-flange bolts (3/8 x 1 inch) and 2 nuts (3/8 inch) as shown in Figure 1. g036548 Figure 2 1. Flange nut (1/4 inch) 4. Hex-head bolt (1/4 x 2-1/2 inches) 2. Spacer (9/32 x 5/8 inch) 5. Flat washer (5/16 inch) 3. Left loop bracket D. 2.
3. Using the dimensions shown in Figure 4, drill 1 hole (5/16 inch) into the outside of the footboard on the left and right sides of the machine. 5. Secure the lower bracket of the windshield support to the left side of the machine using 4 carriage bolts (5/16 x 1 inch) and 4 flange nuts (5/16 inch) in the holes that you drilled in step 2 (Figure 6). g036554 Figure 6 g036553 Figure 4 4. 1. Carriage bolt (5/16 x 1 inch) 3. Lower bracket of windshield support 2.
7. Loosely install the left and right rear plates to the tubes using 4 carriage bolts (5/16 x 1-3/4 inches), 2 backing plates, and 4 flange nuts (5/16 inch) as shown in Figure 8. 9. Loosely install the rear crosslink to the crosslink tubes and rear plates using 4 carriage bolts (5/16 x 1-3/4 inches), 4 carriage bolts (5/16 x 3/4 inch), and 8 flange nuts (5/16 inch) as shown in Figure 10. g036668 g036555 Figure 10 Figure 8 1. Carriage bolt (5/16 x 1-3/4 inches) 4. Flange nut (5/16 inch) 2.
12. Tighten all loose fasteners. 14. 13. Install the sunshade to the front plates using 2 clips, 2 sealing washers, and 2 hex-flange bolts (1/4 x 1 inch) as shown in Figure 12. Install the sunshade to the rear crosslink using 2 hex-flange bolts (1/4 x 1 inch), 2 sealing washers, 2 friction washers, 4 plastic washers, and 2 flange bushings (Figure 13). Important: Apply thread-locking compound Important: Apply thread-locking compound to the hex-flange bolts (1/4 x 1 inch) before installing.
Notes:
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
