Installation Instructions

ManualsBrandsToro ManualsVehiclesWalk Spreader Mounting Kit, Workman GTX Series Utility Vehicle

FormNo.3404-882RevA

WalkSpreaderMountingKit

Workman

GTXSeriesUtilityVehicle

ModelNo.07029

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedorlost.

133-4641

1.Warning—noridersontheattachment.

133-7202

1.Attention—readtheOperator’sManual;donotcarrymore

than45kg(100lb).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3404-882*A

Summary of content (8 pages)

PAGE 1
Form No. 3404-882 Rev A Walk Spreader Mounting Kit Workman® GTX Series Utility Vehicle Model No. 07029 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine. Spreader-mount frame Snap pin Clip bushing Spreader-pivot shaft Left spreader ramp Right spreader ramp Flange-head screw ( 5/16 x 1-1/2 inches) Flange nut (5/16 inch) Clevis pin Hairpin cotter 1 2 2 1 1 1 4 4 1 1 Install the walk-speader mount (for machines with a plastic cargo bed).
PAGE 3
Installing the Walk-Spreader Mount to the Rear of the Machine For Machines with a Plastic Cargo Bed 1. Install the 2 clip bushings to the spreader-mount frame (Figure 2). Figure 4 1. Spreader-pivot shaft 2. Spreader ramp 4. Align the holes on the spreader-pivot shaft with the holes on the left and right spreader ramps, and secure them using the 4 flange-head screws (5/16 x 1-1/2 inches) and 4 flange nuts (5/16 inch) as shown in Figure 5. Figure 2 1. Spreader-mount frame 2. Clip bushing 2.
PAGE 4
Important: If you use the spreader mount while in transport mode without the spreader installed, secure the spreader-ramp assembly using the 2 snap pins as shown in Figure 10. 6. Insert the assembled spreader mount into the machine receiver tube (Figure 7). Figure 7 1. Receiver tube 2. Assembled spreader mount Figure 10 1. Snap pins 7. Secure the assembled spreader mount to the receiver tube using the clevis pin and hairpin cotter (Figure 8). Figure 8 1. Clevis pin 2. Hairpin cotter 8.
PAGE 5
Installing the Walk-Spreader Mount to the Rear of the Machine For Machines with a Steel Cargo Bed Repeat steps 1 through 8 of Installing the Walk-Spreader Mount to the Rear of the Machine (page 3).
PAGE 6
Installing the Walk-Spreader Mount to the Front of the Machine For Machines With or Without the Brush Guard Kit Installed Repeat steps 1 through 8 of Installing the Walk-Spreader Mount to the Rear of the Machine (page 3).
PAGE 7
Operation Installing a Spreader onto the Walk-Spreader Mount 1. Walk the spreader up the spreader ramps. 2. Engage the spreader axles using the axle holders (Figure 14). Figure 14 1. Axle holders 3. Align the kickstand on the spreader between the kickstand-retention tabs on the spreader-mount frame (Figure 15). 4. Secure the spreader to the spreader-mount frame using a snap pin (Figure 15). Figure 15 1. Kickstand-retention tabs 2.
PAGE 8