Installation Instructions

ManualsBrandsToro ManualsAttachmentsLight Kit, Greensmaster 3150/3250-D or Triflex Traction Unit

FormNo.3393-873RevA

LightKit

Greensmaster

3150/3250-DorTriex

™

TractionUnit

ModelNo.04554

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

127–6126

1.Headlights3.Headlightsandrearlights

2.Off

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3393-873*A

Summary of content (8 pages)

PAGE 1
Form No. 3393-873 Rev A Light Kit Greensmaster® 3150/3250-D or Triflex™ Traction Unit Model No. 04554 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Installation 1 Installing the Brackets and Light Assemblies Parts needed for this procedure: 2 Light Assemblies 1 Left bracket 1 Right bracket 2 U-bolt 4 Nuts Figure 2 1. Bimini shade bracket 2. Light kit bracket For Greensmaster 3250 models with a round tube ROPS, the bracket is not needed. Install the light assembly directly onto the ROPS tabs. Procedure 1. Park the machine on a level surface, turn off the engine, and remove the key. 2.
PAGE 3
2 Installing the Wiring Harness Parts needed for this procedure: 1 Wiring harness 10 Cable ties (14.5 inch) 2 Cable ties (7.25 inch) 1 Wiring harness adapter (Greensmaster 3150 and 3250 models prior to 2015 only) 1 Splice, 12-10 awg (Greensmaster 3150 models prior to 2015 only) 2 Splice, 16-14 awg (Greensmaster 3150 and 3250 models prior to 2015 only) Figure 4 Greensmaster 3150 Procedure 1. Route the wiring harness, along the ROPS and under the seat, as shown in Figure 3, Figure 4, or Figure 5.
PAGE 4
For the Greensmaster 3150 models built before 2015: 3 Contact an Authorized Service Dealer to see the electrical schematics to locate the terminals to splice. 1. Route the light kit harness from the light assemblies on the ROPS to the light kit terminals (J13 and J14) on the machine harness, located behind the seat (Figure 6).
PAGE 5
6. Install the console shroud. 7. Connect the negative battery cable. Installing the Switch for the Triflex Traction Units 1. Remove the 7 hex bolts securing the console cover in place and remove the console cover. 2. From inside the console, press the plug out of the hole (Figure 10). Figure 8 1. Fuse 2. Fuse block 5. Install the console shroud. 6. Connect the negative battery cable.
PAGE 6
Operation 4 Operating the Light Switch Installing the Rear-Light Kit (Optional) Aim lights as desired and tighten the mounting nuts. The light switch has 3 positions; refer to Figure 12. Parts needed for this procedure: 1 Rear-light kit (optional) Procedure Install the rear-light kit assemblies as shown in Figure 11. Figure 12 1. Headlights 2. Off Figure 11 1. Front light assembly 4. Nut (to secure the U-bolt) 2. Rear light assembly 5. Lock washer 3. Bolt 6.
PAGE 7
Notes: 7
PAGE 8