Form No. 3374-295 Rev C Reelmaster® 7000-D 4-Wheel Drive Traction Unit Model No. 03708N—Serial No. 313000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the right front frame member of the product. Write the numbers in the space provided.
Contents Fuel System Maintenance ....................................... 40 Fuel Tank ........................................................... 40 Fuel Lines and Connections................................ 40 Servicing the Water Separator ............................. 40 Fuel Pick up Tube Screen.................................... 40 Bleeding Air from the Injectors........................... 41 Electrical System Maintenance................................ 41 Charging and Connecting the Battery ..........
Preparation Safety • While mowing, always wear substantial footwear, long trousers, hard hat, safety glasses, and ear protection. Long hair, loose clothing, or jewelry may get tangled in moving parts. Do not operate the equipment when barefoot or wearing open sandals. • Thoroughly inspect the area where the equipment is to be used and remove all objects which may be thrown by the machine. • Warning—Fuel is highly flammable.
• • • • • • • • • • • • • – Do not turn sharply. Use care when reversing. – Use counterweight(s) or wheel weights when suggested in the operator's manual. Stay alert for holes in the terrain and other hidden hazards. Watch out for traffic when crossing or near roadways. Stop the blades rotating before crossing surfaces other than grass. When using any attachments, never direct discharge of material toward bystanders nor allow anyone near the machine while in operation.
• Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running. • Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools. • Raise the cutting units when driving from one work area to another.
• If major repairs are ever needed or if assistance is desired, contact an Authorized Toro Distributor. • Use only Toro-approved attachments and replacement parts. The warranty may be voided if used with unapproved attachments. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117-4763 1. To engage the parking 2.
98-4387 1. Warning—wear hearing protection. 119-3905 1. Reel speed 93-6688 1. Warning—read the instructions before servicing or performing maintenance. 2. Cutting hazard of hand or foot—stop the engine and wait for moving parts to stop. 117-4765 1. Read the Operator's Manual. 2. Do not use starting aids. 20A 10A 117-4766 1. Cutting/dismemberment hazard; fan—stay away from moving parts. 10A 10A 10A 7.5A 7.5A 7.5A TEC-5002 2A 60A 120-1672 120-1672 117–2718 1. Starter, 20A 5. Gauges, 10A 2.
120-1683 1. Warning—read the Operator's Manual, do not operate this machine unless you are trained. 4. Warning—do not park the machine on slopes; engage the parking brake, lower the cutting units, stop the engine and remove the ignition key before leaving the machine. 2. Warning—read the Operator's Manual before towing the machine. 3.
Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 5. Read the Operator's Manual. 120-1671 120-1670 1.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 5 6 Use Qty. No parts required – Adjust the support rollers Front hose guide-R.H. Front hose guide-L.H. 1 1 Install the cutting units No parts required – Adjust the turf compensation spring. Cutting unit kickstand 1 Install the Cutting Unit Kickstand. No parts required – Grease the machine.
2. Remove the shipping brackets and discard. 3. Remove the cutting units from the cartons. Assemble and adjust as described in the cutting unit Operator's Manual. 4. Make sure the counter weight (Figure 4) is installed to the proper end of the cutting unit as described in the cutting unit Operator's Manual.
nut. The bolt head is to be positioned to the outer side of the tab as shown in Figure 6. Figure 7 Figure 6 1. Opposite carrier frame tab 2. Rod bracket D. Mount the rod bracket to the cutting unit tabs with the carriage bolts and nuts (Figure 6). Also, on the cutting unit, mount the left hand hose guide to the front of the cutting unit tabs when reinstalling the rod bracket (Figure 8).
Note: 32 inch cutting units are not equipped with pivot spacers. 1 2 2 1 3 3 5 G015978 4 Figure 10 1. Hex socket screw 2. Pivot spacer 3. Carrier frame 4. Flange lock nut 4 G015976 7. Lower all the lift arms completely. Figure 11 8. Coat the carrier frame shaft with clean grease (Figure 11). 9. For the front cutting units, slide a cutting unit under the lift arm while inserting the carrier frame shaft up into the lift arm pivot yoke (Figure 11).
A. Remove the lynch pin and washer securing the lift arm pivot shaft to the lift arm and slide the lift arm pivot shaft out of the lift arm (Figure 13). Figure 13 1. Lift arm pivot shaft lynch pin and washer B. Insert the lift arm yoke onto the carrier frame shaft (Figure 11). Figure 15 C. Insert the lift arm shaft into the lift arm and secure it with the washer and lynch pin (Figure 13). 1. Reel drive motor 13. Secure the lift arm chain to the chain bracket with the snapper pin (Figure 14).
Figure 16 1. Turf compensation spring 3. Spring rod 2. Hair pin cotter 4. Hex nuts Figure 17 1. Cutting unit kickstand 2. Tighten the hex nuts on the front end of the spring rod until the compressed length of the spring is 6.25 inches (15.9 cm) (Figure 16). Secure the kickstand to the chain bracket with the snapper pin (Figure 18). Note: When operating on rough terrain decrease the spring length by 1/2 inch. Ground following will be slightly decreased.
Product Overview 5 Controls Greasing the Machine Brake Pedals Two foot pedals (Figure 19) operate individual wheel brakes for turning assistance and to aid in obtaining better side hill traction. No Parts Required Procedure Pedal Locking Latch Before the machine is operated, it must be greased to ensure proper lubrication. Refer to Lubrication section. Failure to properly grease the machine will result in premature failure of critical parts.
Charge Indicator toward you to the most comfortable position and then release the pedal. The charge indicator (Figure 21) illuminates when the system charging circuit malfunctions. Mow Speed Limiter Key Switch When the mow speed limiter (Figure 20) is flipped up it will control the mow speed and allow the cutting units to be engaged. Each spacer adjusts the mowing speed by ½ mile per hour. The more spacers you have, on the top of the bolt the slower you will go.
the machine, with the cutting units in the down position, press the lift switch down to allow the cutting units to float and mow. has two positions R (manual reverse) and Auto (normal). Refer to Engine Cooling Fan Operation in the Operation Section of manual. Throttle Control Bag Holder Move the control (Figure 21) forward to increase the engine speed and rearward to decrease the speed. Use the bag holder (Figure 22) for storage.
Weight gauge Indicates when the seat is adjusted to the weight of the operator (Figure 26). Height adjustment is made by positioning the suspension within the range of the green region. Figure 24 1. Reel speed controls Fuel Gauge Figure 26 The fuel gauge (Figure 25) indicates the level of fuel in the tank. 1. Weight gauge 4. Seat back adjusting lever 2. Weight adjusting lever 5. Arm rest adjusting knob 3. Fore and Aft adjusting lever Weight Adjusting Lever Adjust for operator weight (Figure 26).
Specifications Note: Specifications and design are subject to change without notice. Traction Unit Specifications Width of cut 121 inches (307 cm) Overall width, cutting units down 136 inches (345 cm) Overall width, cutting units up (transport) 94 inches (239 cm) Overall length 145.8 inches (370 cm) Height with ROPS 87 inches (220 cm) Track Width, front 90 inches (229 cm) Track Width, rear 55.
Operation 1. Park the machine on a level surface. 2. Unlock the hood latches and open the hood (Figure 27). Note: Determine the left and right sides of the machine from the normal operating position. CAUTION This machine produces sound levels in excess of 85 dBA at the operator's ear and can cause hearing loss through extended periods of exposure. Wear hearing protection when operating this machine.
Figure 29 1. Oil fill cap Note: When using different oil, drain all old oil from the crankcase before adding new oil. Figure 30 5. Install the oil fill cap and dipstick. 1. Expansion tank 6. Close the hood and secure it with the latches. 2. Check the coolant level in the radiator. The radiator should be filled to the top of the filler neck and the expansion tank filled to the FULL mark (Figure 30).
WARNING DANGER Fuel is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness. In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. • Avoid prolonged breathing of vapors. • Use a funnel and fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any fuel that spills. • Keep face away from nozzle and gas tank or conditioner opening.
140 to 160 Viscosity Index ASTM D2270 Pour Point, ASTM D97 -34°F to -49°F Industry Specifications: Vickers I-286-S (Quality Level), Vickers M-2950-S (Quality Level), Denison HF-0 DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the fuel vapors. A fire or explosion from fuel can burn you and others and can damage property. • Always place fuel containers on the ground away from your vehicle before filling.
3. Remove the dipstick from the filler neck and wipe it with a clean rag. Insert the dipstick into the filler neck; then remove it and check the fluid level. The fluid level should be between the two marks on the dipstick. 4. If the level is low, add the appropriate fluid to raise the level to the upper mark. 5. Install the dipstick and cap onto the filler neck. When the temperature is less than 20°F (-7°C), the starter motor can be run for 30 seconds on then 60 seconds off for 2 attempts.
pedal is released, it is strongly recommended that the engine be stopped before rising from the seat. neutral position. The engine should kill. If the engine does not kill, there is a malfunction in the interlock system that should be corrected before beginning operation. To check the operation of the interlock switches, perform the following procedure: 1. Drive the machine slowly to a large, relatively open area. Lower the cutting unit, stop the engine, and apply the parking brake.
Figure 35 1. Spring 2. Spring actuator 4. Move the spring actuator to the desired hole location and secure with locknut. 5. Repeat the procedure on the remaining spring. Figure 34 1. Reel speed control knob Adjusting the Lift Arm Turn Around Position Adjusting the Lift Arm Counterbalance 1. Position the machine on a level surface, lower the cutting units, stop the engine, engage the parking brakes, and remove the key from ignition switch. 2.
Jacking Points turn around height or move the switch down to decrease the lift arm turn around height. Tighten the mounting screws. • On the front of the machine on the frame on the inside of each drive tire • On the rear of the machine at the center of the axle Pushing or Towing the Machine Tie Downs In an emergency, the machine can be moved forward by actuating the bypass valve in the variable displacement hydraulic pump and pushing or towing the machine.
Verifying the Interlock Switch Function If the diagnostic light is not illuminated when the key switch is in the On position, this indicates that the electronic controller is not operating. Possible causes are as follows: 1. Park the machine on a level surface, lower the cutting units, stop the engine, and engage the parking brake. 2. Remove the access panel located beneath the front of the seat (Figure 39). 3. Locate the wire harness and connectors near the controller (Figure 39).
7. The “inputs displayed” LED, on the lower right column of the Diagnostic ACE, should be illuminated. If the “outputs displayed” LED is illuminated, press the toggle button, on Diagnostic ACE, to change LED to “inputs displayed”. forth, press the toggle button once. This may be done as often as required. Do not hold the button. 8. Sit on the seat and attempt to operate the desired function of the machine. The appropriate output LEDs should illuminate to indicate that the ECM is turning on that function.
Warning System brakes can be used to assist in turning the machine. However, use them carefully, especially on soft or wet grass because the turf may be torn accidentally. Another benefit of the brakes is to maintain traction. For example, in some slope conditions, the uphill wheel slips and loses traction. If this situation occurs, depress the uphill turn pedal gradually and intermittently until the uphill wheel stops slipping, thus, increasing traction on the downhill wheel.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Torque the wheel nuts. After the first 50 hours • Change the engine oil and filter. After the first 200 hours • Change the planetary gear drive oil. • Change the rear axle lubricant. • Change the hydraulic filters.
Daily Maintenance Checklist Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Sat.
Service Interval Chart Figure 41 CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance.
Premaintenance Procedures Lubrication Greasing the Bearings and Bushings Removing the Hood Service Interval: Every 50 hours 1. Release hood latches (Figure 42) and pivot open the hood. The machine has grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. If the machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation or immediately after every washing.
• Steering cylinder ball joints (2) (Figure 45) • Cutting unit carrier frame (2 per cutting unit) (Figure 47) • Cutting unit lift arm pivot (1 per cutting unit) (Figure 47) Figure 47 Figure 45 1. Top fitting on king pin • Tie rod ball joints (2) (Figure 45) • King pin bushings (2) (Figure 45). The top fitting on the king pin should only be lubricated annually (2 pumps).
Engine Maintenance which could force dirt through the filter into the intake tract. Servicing the Air Cleaner This cleaning process prevents debris from migrating into the intake when the primary filter is removed. Service Interval: Every 400 hours 3. Remove and replace the primary filter (Figure 50). Check the air cleaner body for damage which could cause an air leak. Replace if damaged. Check the whole intake system for leaks, damage or loose hose clamps.
Adjusting the Throttle Servicing the Engine Oil and Filter Adjust the throttle cable (Figure 54) so that the governor lever on the engine contacts the high speed set bolt at the same point that the throttle cable contacts the end of the slot in the control arm. Service Interval: After the first 50 hours Every 400 hours Change the oil and filter initially after the first 50 hours of operation; thereafter change the oil and filter every 400 hours. 1.
Servicing the Water Separator Fuel System Maintenance Service Interval: Before each use or daily—Drain water or other contaminants from fuel filter/water separator. DANGER Every 400 hours—Replace the fuel filter canister. Under certain conditions, diesel fuel and fuel vapors are highly flammable and explosive. A fire or explosion from fuel can burn you and others and can cause property damage. Drain water or other contaminants from water separator daily.
Bleeding Air from the Injectors Electrical System Maintenance Note: This procedure should be used only if the fuel system has been purged of air through normal priming procedures and the engine will not start. Charging and Connecting the Battery 1. Loosen the pipe connection to the No. 1 injector nozzle and holder assembly at the injection pump (Figure 56).
2. Connect a 3 to 4 amp. battery charger to the battery posts. Charge the battery at a rate of 3 to 4 amperes for 4 to 8 hours. jelly, or light grease to prevent corrosion. Slide the rubber boot over the positive terminal. 6. Close the console panel and secure the latch. 3. When the battery is charged, disconnect the charger from the electrical outlet and battery posts. WARNING Battery terminals or metal tools could short against metal components causing sparks.
Fuses The fuses are located under the operators control panel. 20A 10A 10A 10A 10A 7.5A 7.5A 7.5A TEC-5002 2A 60A 120-1672 Figure 59 Figure 61 1. Fuses Unhook the latch and raise the operator's console panel (Figure 60) to expose the fuses (Figure 61). Figure 60 1. Operator's console panel 2.
Drive System Maintenance 3. If the oil level is low, remove the plug at the 12 o’clock position and add oil until it begins to flow out of the hole at the 3 o’clock position. 4. Re-install both plugs. Checking the Torque of the Wheel Nuts 5. Repeat steps 1 through 4 on the opposite planetary gear assembly.
Figure 65 2. Fill plug 1. Check plug g019743 Figure 64 1. Brake housing 2. Drain plug Changing the Rear Axle Lubricant 4. When all of the oil has drained from both locations, re-install the plug in the brake housing. Service Interval: After the first 200 hours 5. Rotate the wheel until the open plug hole in the planetary is at the twelve o'clock position. Every 800 hours 1. Position the machine on a level surface. 6. Through the open hole, slowly fill the planetary with 22 ounces. (0.
Adjusting the Traction Drive for Neutral The machine must not creep when traction pedal is released. If it does creep, an adjustment is required. 1. Park machine on a level surface, shut engine off, position speed control into LOW range and lower cutting units to the floor. Depress only the right brake pedal and engage the parking brake. Figure 68 2. Jack up left side of machine until left front tire is off the shop floor. Support machine with jack stands to prevent it from falling accidentally. 1.
Cooling System Maintenance Servicing the Engine Cooling System Service Interval: Before each use or daily Remove debris from the engine area, oil cooler and radiator daily. Clean them more frequently in dirty conditions. 1. Unlatch and swing open rear screen (Figure 70). Clean the screen thoroughly of all debris. Figure 71 Note: To remove the screen, lift off the hinge pins. 1. Oil cooler latches 3. Pivot the oil cooler rearward.
Brake Maintenance Belt Maintenance Adjusting the Service Brakes Servicing the Alternator Belt Adjust the service brakes when there is more than 1 in. (25 mm) of “free travel" of the brake pedal, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before braking resistance is felt. Service Interval: Every 100 hours 1. Disengage the locking latch from the brake pedals so that both pedals work independently of each other. 1. Proper tension will allow 3/8 in.
Hydraulic System Maintenance 3. Lubricate the new filter gasket and fill the filter with hydraulic fluid. Changing the Hydraulic Fluid Service Interval: Every 800 hours Change the hydraulic fluid after every 800 operating hours, in normal conditions. If the fluid becomes contaminated, contact your local Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. 1. Turn the engine off and raise the hood. 2.
Checking the Hydraulic Lines and Hoses Cutting Unit Maintenance Backlapping the Cutting Units Service Interval: Before each use or daily Inspect the hydraulic lines and hoses daily for leaks, kinked lines, loose mounting supports, wear, loose fittings, weather deterioration, and chemical deterioration. Make all necessary repairs before operating. WARNING Contact with the reels or other moving parts can result in personal injury.
Cleaning Servicing the Spark Arrestor Muffler Service Interval: Every 200 hours Every 200 hours operation, clear the muffler of carbon buildup. 1. Remove the pipe plug from the clean-out port at the lower side of the muffler. CAUTION The muffler may be hot and could cause injury. Be careful while working around the muffler. Figure 77 1. Front backlap lever 2. Start the engine.
Storage Engine 1. Drain the engine oil from the oil pan and install the drain plug. 2. Remove and discard the oil filter. Install a new oil filter. 3. Refill the oil pan with 10 qt. (9.5 l) of SAE 15W-40 CH-4, CI-4, higher motor oil. 4. Start the engine and run it at idle speed for approximately two minutes. 5. Stop the engine. 6. Flush the fuel tank with fresh, clean diesel fuel. 7. Secure all of the fuel system fittings. 8. Thoroughly clean and service the air cleaner assembly. 9.
Schematics Hydraulic Schematic (Rev.
Electrical Schematic-Sheet 1 (Rev.
Electrical Schematic-Sheet 2 (Rev.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
