Installation Instructions

ManualsBrandsToro ManualsRiding ProductsWeather Protection Kit, Groundsmaster 4300 or Reelmaster 5010 Series Traction Unit with Security Cage

FormNo.3434-151RevA

WeatherProtectionKit

Groundsmaster

4300orReelmaster

5010SeriesTractionUnit

withSecurityCage

ModelNo.03626

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Clasp

Claspmount

Screw

Nut8

Installtheclasps.

Leftdoorcover

Rightdoorcover1

Installthelargecovers.

Rightcover1

Leftcover

Lowerleftcover

Lowerrightcover1

Rearcagecover1

Installthesmallcovers.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

Performthefollowingproceduretopreparethemower

forattachingtheblowerandnishingkit.

1.Parkthemachineonalevelsurface,disengage

thePTO,andengagetheparkingbrake.

2.Shutoffthemachine,removethekey,andwait

forallmovementtostopbeforeleavingthe

operatingposition.

3.Cleanthesurfacesofthecagewherethehoop

andhookclosurewilladheredtowithalcohol

wipes.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3434-151*A

Summary of content (4 pages)

PAGE 1
Form No. 3434-151 Rev A Weather Protection Kit Groundsmaster® 4300 or Reelmaster® 5010 Series Traction Unit with Security Cage Model No. 03626 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. No parts required – Clasp Clasp mount Screw Nut Left door cover Right door cover Right cover Left cover Lower left cover Lower right cover Rear cage cover 4 8 8 8 1 1 1 1 1 1 1 Prepare the machine.
PAGE 2
. 2 Install the clasps as shown in Figure 2. Installing the Clasps Parts needed for this procedure: 4 Clasp 8 Clasp mount 8 Screw 8 Nut Procedure 1. Measure the location to install the clasps on each door as shown in Figure 1. g295829 Figure 2 g295828 Figure 1 1. Installed clasp 3. 27.13 cm (10-21/32 inches) 2. Install the clasps on the 4. 58.72 cm (23-1/8 inches) first row of “X” on the door.
PAGE 3
1. Remove half of the hoop and hook closure straps, with the adhesive, from each door cover (Figure 3). 2. Peal the film off of the adhesive and place it in the position for each door (Figure 3). 3. Install the covers for the doors by aligning the holes with the clasps and press the hoop and hook closure straps together around each door. g295830 Figure 3 1. Right door cover 3. Left door cover 2. Remove the hoop and hook straps from the covers.
PAGE 4
Installing the Small Covers Parts needed for this procedure: 1 Right cover 1 Left cover 1 Lower left cover 1 Lower right cover 1 Rear cage cover Procedure Note: For the small covers, do not separate the hoop and hook closure straps. Use the whole cover for positioning. 1. Position and ensure the location of the cover before peeling off the film for the adhesive (Figure 4). 2. Peel the film off of the adhesive and place the cover in position (Figure 4). 3.