FORM NO. 3311-266 Rev. A RECOIL {6 BLADE} OPERATOR’'S MODEL NOS. 03215 — 90001 & UP MANUAL L 70" {1.78 m) PROFESSIONAL® J PRICE $1.
FOREWORD This Operator’s Manual has been especially prepared for your information and guidance in the operation and care of your new Toto mower. Properly adjusted, operated and maintained, this Toto mower wil} respond quickly and easily to every reasonable demand and give years of reliable service, Tore mowers have been manufactured by an organization of mowing machinery specialists for over ditty years. Each machine is carefully inspected and tested before leaving the factory.
SAFETY INSTRUCTIONS 9. Since gasoline is highly flammable, handle it carefully. A. Use an approved gasoline container. B. Do not remove cap from fuel tank when engine is hot or running. C. Do not smoke while handling gasoline. D. Fill fuel tank outdoors and not over one inch {25 mm} from the top of the tank, not the filler neck, Do not overfill. E. Wipe up any spilled gasoline. WHILE OPERATING 10. Do not run the engine in a confined area without adequate ventilation.
SAFETY INSTRUCTION DECALS The following safety and instruction decals are installed on the unit. If any become damaged or illegible, replace them. Decals are listed in your Parts Catalog. Order replacements from your Authorized Toto Distributor, WARNING NEVER PLACE HANDS OR FEET cay STARTING INSTRUCTIONS 4. PAGE TRACTION AND CUTTING UNIT CONTROL LEVERS IN NEUTRAL POSITION. 2 SET CHOKE AND THROTTLE AS REQUIRED. {5EE OPERATORS MANUAL] 3. TERR KEY O “RUN.” 4 START ENGINE 5.
SPECIFICATIONS Differential: Stamped steel case with ROFL formed hardened spur gears. Reduction: Engine to reel 4.75:1 Traction Wheel Drive-Forward 41.00:1 Traction Wheel Drive-Reverse 43.06:1 Wheels: Drive wheels and sulky. #14 gauge (18.97 mm) steel discs. Steel hubs. Tires: 16 x 6.50 x B tubeless Terra-tire Clip: .79” blade reel. Construction: Welded Steel frame consisting of (45 mm) square and round steel tubing. Engine base and other supporting members are formed sheet steel.
SETTING UP INSTRUCTIONS 1. Break shipping bands and remove top from crate. 2. ‘Remove side of crate, then the top and one side support board at rear of machine (Fig. 1} 3. Clip the bands “A’ securing the front and rear of machine to pallet, remove the stud and handle assembly “B"” from the frame (Fig. 1). Figure 3 5. Remove roll pin at top of steering shaft and install steering handle {Fig. 4}, Figure 1 | Figure 4 4. Rotate sulky “A" out into position, install stud 6. Pl seer Y . Terr .
SETTING UP INSTRUCTIONS 7. Connect switch cable to interlock cable (Fig. 6). e TRUTHER CABLE, Figure 8 11. Install transport link “A” to center pin on rear of cutting unit and secure with cotter pin (Fig. 8}, 12. Check cutting unit drive chains for proper adjustment. Adjust, if necessary: refer to Cutting Unit Chain Adjustments, page 18. A CAUTION FRONT COUNTERBALANCE SPRING Since extension spring is pensioned, GRASP SUPPORT ARMS when installing or removing transport finks from cutting units Fig. 9). .
SETTING UP INSTRUCTIONS 13, Adjust cutting unit reel to bed knife 1o assure proper cutting. performance will be 10}. Refer to Reel Adjustment; page 14; for proper adjustment procedures. 14, Mower height is set at factory inches (27.8 mm} height-of cut. Set cutting units on a level surface and-use center. link .and hols A’ to adjust to-a different height setting, if desired (Fig. 11). Refer'to page 14 for more complete adjustment instructions.’ 15, Tires inflated for shipment.
OPERATION With the 707 {1.78 m} Professional on a level surface, remove the oil filter cap (see photo below). Fill crankcase to the full mark (F) on the dipstick. Fill engine to proper level with SAE 30MS motor oil {Fig, 14}, Ol CHART APl Service M8 Sings Multiplier Air Temperature Viscosity Of Viscosity Oil Above 30°F (-1°C SAE 18°0) SAE 10 SAE 10W-30 Below 0°F SAE 5-20 Figure 14 For & smoother running engine change oil every 26 operating hours; more often under dusty conditions.
OPERATION A CAUTION Do not disconnect ‘the safety switches “because they are for the operator’s protection. Check operation of the switches daily to assure the interlock system.is operating correctly. 1 a-switch is defective, replace it-before operating the machine. Replace the switches once a year to assure. maximum safety. Assure the ~machine is in an open area, free of obstructions and bystanders, 1. Move reel drive lever to DISENGAGE position and traction lever to N (NEUTRAL]) position. 2.
OPERATION The rear cutting unit is put into transport position by lifting the cutting unit and hooking the hanger assembly ‘A’ over rod of lower plate of the sulky {Fig. 20). REAR TRANSPORT POSITION Figure 20 IMPORTANT: Do not engage cutting unit drive with cutting units in transport position, EVALUATING QUALITY OF CUT FREQUENCY OF MOWING: The frequency of mowing is as important as the height-of-cut.
MAINTENANCE Figure 23 12 Figure 22 LUBRICATION 1. Grease fitting — use good grade of gun grease every eight hours’ of operation. There are 13 grease fittings in all (Fig. 22). Two fittings on rear cutting unit are not shown but are in the same position as those on front cutting units. 2. Linkage — apply a few drops of good grade of lubricating oil every eight hours of operation, 3. Engine — use a good grade of SAE 30MS engine oil (capacity is 2-1/2 pints — 1.183 Check engine oil level.
MAINTENANCE SERVICING AIR CLEANER 1. Remove wing nut and lift air cleaner from carburetor, 2. Take off cover and lift out cartridge. 3. Cartridge should be cleaned every 50 hours by gently tapping on a flat surface. 4. Replace cartridge . if bent, crushed or damaged and under extreme dust conditions after 100 operating hours. 5. Clean or replace cartridge when loss of power is noticeable. 6. Be sure cartridge fits on bottom adapter plate, and wing nut on top adapter plate is finger tight.
MAINTENANCE REEL ADJUSTMENT (Fig. 27} REEL ADJUSTMENT: To adjust reel toward bed knife for proper cutting, turn hex bolt head ‘A’, on each end of cutting unit counterclockwise turner. Using a plastic head hammer, smartly tap on head ‘A’ to insure seating of the bolt head against side plate flange, end insure positive reel movement to the bed knife. Proper reel to bed knife adjustment is achieved when each reel blade will crease paper across its full length. A {36.
MAINTENANCE SEAR {10.8 om} Figure 31 DIFFERENTIAL DRIVE CHAIN (Fig, 32) DIFFERENTIAL DRIVE CHAIN ADJUSTMENT: Loosen fasteners ‘A’ and rotate.shaft and housing assembly *B’ as shown until chain is snug — but not taut (Fig. 32). Care should be taken to assure alignment of shaft assembly before re tightening fasteners ‘A’. Alignment is correct when grooves of traction pulley mesh with grooves of engine pulley. Figure 32 TRACTION DRIVE CHAIN (Fig.
MAINTENANCE ADJUSTING i Figure 35 TRACTION BELT REPLACEMENT {Fig. 36} TRACTION BELT REPLACEMENT: Loosen belt guides ‘A, Work. bat off end of engine pulley ‘B’ and traction drive pulley ‘C’, Slide belt edgewise between traction pulley and reel drive pulley. Reverse process to install new belt. Readjust belt to Belt Guides, page WOODEN BLOCKS HERE Figure 37 Remove cap screw and washers ‘A’ from axle at the wheel hub, right side (Fig. 35). Pull wheel, tire and hub assembly from axle.
% ot S MAINTENANCE Remove axle by pulling on left wheel (Fig. 40). The tire, wheel and differential do not need to be removed. Figure 40 At this point the counter shaft assembly ‘A’ is held only by belt ‘B’ and front cutting unit drive chain ‘D’ {Fig. 41}, Disconnect chain, then remove belt ‘B* and replace. At either end of the counter shaft assembly are spacer washers ‘G’ {see inset). The number of spacer washers used may vary with.
MAINTENANCE FIG. FIG. £16.43 S Figure 42 CUTTING UNIT CHAIN ADJUSTMENTS Front Cutting Unit Drive {Fig. 43) To tighten front cutting unit drive chain: 1. Remove screw 'J'. 2. Move one shim ‘H’ on each of the four corners {as shown) of the intermediate frame 'G’. 3. Be certain that one shim {or the same number) is moved on each corner and that screw ‘J’ is then reinserted.
gyt MAINTENANCE Rear Cutting Unit Drive {Fig. tighten rear cutting unit drive chain: 1. Remove screw ‘T, 2. Move shims ‘K’ and ‘R’ {one shim ‘R’ on each side of reel), . 3. f necessary, nut ‘N may be slightly loosened to remove shim ‘K’, and re tightened after move. 4, Care must be taken so that nut ‘M’ does not rotate during adjustment as this will affect the attitude of the reel and thus change the cutting height slightly. 5. Reinsert screw ‘T" and nut 'S". 6.
ELECTRICAL TROUBLE SHOOTING IMPORTANT: Before “troubleshooting interlock system, assure all wires are connected correctly and making good contact. Check for short circuits between wires and other parts. Repair short circuits before troubleshooting any SCREENWRITER BLE TE LIGHT SLUE problem. paranormal WIRING DIAGRAM LG8 B To engine condescension cosine g OO Switch Condition Cause Correction Engine fails 10 start or run, 1. Defective key switch. 2. Electrical wire grounded to vehicle. 3.
N Py s MAINTENANCE BED KNIFE & REEL SHARPENING Your 70”7 {1.78 m} Professional is equipped with hard coated bed knives. This hard coating processes a very hard layer of satellite material applied to the front face of the knife. This will help keep your 70" (1.78 mj} Professional sharper longer. DO NOT GRIND THE HARD COATED FACE OF THE KNIFE. When Is Sharpening Necessary? The first indication that sharpening is necessary is .when the grass is not cleanly cut.
MAINTENANCE 1. Adjust the reel to bed knife to obtain a light contact, 2. Operate the lapping machine so the reel turn sin reverse direction for about three minutes. Apply lapping solution continuously and evenly along entire length of the reel. 3, Again, lightly adjust the bed knife and reel. Then lap for approximately two additional minutes, Apply lapping solution continuously. 4. Wash off all lapping solution. 5.
MAINTENANCE RECORD Hours oit Air Cleaner Sharpener Date Used Change Service cation Reels Notes ¥ S’ ri?' VIPs
Turf Products costs on walk rotary mowers. Should you feel your TOR is defective and wish to rely on The Toto Promise, the following procedure is recommended: 1, Contest your Authorized TOR Distributor {the Yellow Pages of your telephone directory is a good reference source}. 2. The TOR Distribute will advise you on the arrangements that can be made to inspect and repair your product, 3.
