Installation Instructions

ManualsBrandsToro ManualsAttachmentsBeacon Kit, LT3240 Mower

FormNo.3368-280RevA

BeaconKit

LT3240Mower

ModelNo.02848

InstallationInstructions

Installation

1.Parkthemachineonalevelsurface,stoptheengine,

engagetheparkingbrake,lowerthecuttingunitsand

removethekeyfromtheignitionswitch.

2.Disconnectthenegative(–)batteryleadrstand

thendisconnectthepositive(+)batterylead.

WARNING

Wearsafetygogglesandrubbergloveswhen

workingwithbatteries.Sincethegasesare

explosive,keepopenamesandelectricalspark

awayfrombatteries.Donotsmoke.

3.Disconnectatoneendthecablestaylocatedonthe

rearcover.

4.Identifyandunscrewthe2enginecover/rear

screenassemblypivotboltsandremovetheengine

cover/rearscreenassemblyfromthemachine.Refer

totheLT3240PartsListandOperatorManualas

appropriate.

WARNING

Theenginecoverismadefromglassreinforced

plastic,alwaysweareyeandmouthprotectionto

preventglassparticles,whicharecreatedwhen

drilling/machiningthematerial,fromcoming

intocontactwitheyesorfrombeingingested.

Ifswallowedseekmedicalattention.Intheevent

ofcontactwitheyes,washwithrunningwater

andseekmedicalattentionifsymptomspersist.

5.Aligntheholetemplate(Figure5)ontheengine

coveranddrilltheholesshown(Figure1).

G016053

Figure1

1.Enginecover2.Template

6.Reassembletheenginecover/rearscreenassembly

tothemachine.

7.Raisethefrontplatformtogainaccesstothecontrol

panelelectricalconnections.

8.Removeoneoftheblankingplugsbehindthe

parkinglever.Pushthebeaconswitchintoposition

(

Figure2).

G016054

Figure2

1.Beaconswitch3.Lens

2.Fuse

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUK.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3368-280 Rev A Beacon Kit LT3240 Mower Model No. 02848 Installation Instructions Installation 1. Park the machine on a level surface, stop the engine, engage the parking brake, lower the cutting units and remove the key from the ignition switch. 2 1 2. Disconnect the negative (–) battery lead first and then disconnect the positive (+) battery lead. WARNING Wear safety goggles and rubber gloves when working with batteries.
PAGE 2
9. Remove the fuse box cover and connect the 5A fuse next to the 3A fuse (Figure 2). 17. Lower the front platform and engine cover and re-secure. 10. From the existing loom, connect the orange wire terminal to the beacon switch no. 5 and the red/orange wire terminal to terminal no. 1. 18. Verify the kit is working properly. Press the rocker switch to turn the beacon on. Note: Ensure the platform fasteners are torqued to 40 N-m. Refer to the LT3240 Operator Manual. 11.
PAGE 3
G016055 Figure 4 3
PAGE 4
WARNING The engine cover is made from glass reinforced plastic, always wear eye and mouth protection to prevent glass particles, which are created when drilling/machining the material, from coming into contact with eyes or from being ingested. If swallowed seek medical attention. In the event of contact with eyes, wash with running water and seek medical attention if symptoms persist.
PAGE 5
Maintenance Maintenance Tips • Verify that the bulb is functional and that the reflector rotates properly. • Clean the beacon regularly with a non petroleum-based cleaner. • Always verify that the beacon is secured firmly to the mower before use. • Ensure that the drain slots are kept clear of debris. • If the mower is going to be stored outdoors, verify that the lens is secured properly to prevent water from entering the beacon.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).