Form No. 3367-853 Rev C 36in (92cm) Mid-Size Flail Attachment Model No. 02720—Serial No. 312000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Contents This product complies with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. Introduction................................................................. 2 Safety ........................................................................... 3 Sound Power Level............................................... 3 Sound Pressure Level ........................................... 3 Vibration Level .................................
Safety and Instructional Decals Safety This equipment has been designed and constructed so that, in so far as is reasonably practical, they meet the safety requirements of European standard EN 12733 and they will not endanger the health and safety of those working with them. This is, however, subject to the machine being properly maintained and used according to the conditions stated in this Operator’s Manual, which have been found necessary as a result of the research and testing of the Toro company.
Product Overview Operation Specifications Note: Determine the left and right sides of the machine from the normal operating position. Note: Specifications and design are subject to change without notice. Length 83.5 inches (212 cm) Width 43.1 inches (109.5 cm) Height 44 inches (112 cm) Weight, cutting unit only 298 lb (135 kg) Engine Speed 3600 rpm Rotor Speed 3000 rpm Number of Blades 24 Setting the Height of Cut You can set the height of cut of the mower from 1/2 to 5-1/2 inches (12.
3. Turn the turnbuckle clockwise to lower the height of cut and counterclockwise to raise it until you reach the desired setting on the height-of-cut gauge (Figure 2). Height-of-cut Position (Height in Inches) Height of Cut (mm) 1/2 13 mm 1 25 mm 1-1/2 38 mm 2 51 mm 2-1/2 64 mm 3 76 mm 3-1/2 89 mm 4 102 mm 4-1/2 114 mm 5 127 mm 5-1/2 140 mm 4. Set the turnbuckle lock to lock the height-of-cut setting in place. Adjusting the Anti-scalp Skids 1.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Maintenance Procedure • Inspect the blades for wear or damage. • Clean under the guards. • Check the rubber discharge guards. Every 50 hours • • • • • Grease the fittings Check the brake. Check the gearbox drive belt for wear or damage. Check the rotor drive belt for wear or damage. Check the gearbox oil level.
Maintaining the Blades Inspecting the Blades Service Interval: Before each use or daily Check the blades for wear or damage paying particular attention to the cutting edge, curved area, and installation hole (Figure 5). If the blade is excessively worn or damaged replace the blade. To ensure a superior quality of cut, keep the blades sharp. Figure 6 1. Blade bolt 2. Blade 3. Nut 2. Discard the blade, nut, and bolt. 3. Install a new blade with a new nut and blade bolt (Figure 6). 4.
Checking the Rubber Discharge Guards Replacing the Gearbox Drive Belt Service Interval: Before each use or daily Service Interval: Every 50 hours—Check the gearbox drive belt for wear or damage. Inspect the rear and the front rubber guards for wear or damage (Figure 8). Replace damaged rubber guards to prevent objects being thrown into the operator’s area. Visually inspect the belt (Figure 10), looking for dirt, wear, cracks, and signs of overheating.
Replacing the Rotor Drive Belt B. Rotate the turnbuckle. Increase the length between the eyebolts to add more tension into the belt or decrease the length to decrease the tension in the belt. Service Interval: Every 50 hours—Check the rotor drive belt for wear or damage. Visually inspect the belt (Figure 11), looking for dirt, wear, cracks, and signs of overheating. If belt is excessively worn or shows any signs of damage, replace the belt. C. Tighten the locknut.
Storage Refer to the traction unit Operator’s Manual for details of machine storage.
International Distributor List Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip. B-Ray Corporation Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Equiver Femco S.A. G.Y.K. Company Ltd. Geomechaniki of Athens Guandong Golden Star Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Ibea S.P.A. Irriamc Irrigation Products Int'l Pvt Ltd. Jean Heybroek b.v. Lely (U.K.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
