Operator's Manual

ManualsBrandsToro ManualsWalk-Behind MowersTransport Wheel Kit, HoverPro 450/500/550 Machine

FormNo.3404-808RevA

TransportWheelKit

HoverPro

450/500/550Machine

ModelNo.02622

Operator'sManual

Safety

•Beforeusingthiskit,refertothemachineOperator’s

Manualsafetysection.

•Donotliftthemachineontothetransportwheelkitor

movethemachineusingthetransportwheelkitwhile

theengineisrunning.

Vibration

Measuredvibrationlevelforthelefthand=7.7m/s

(model

02602);3.1m/s

(model02604);5.8m/s

(model02606).

Measuredvibrationlevelfortherighthand=4.8m/s

(model

02602);4.4m/s

(model02604);4.0m/s

(model02606).

UncertaintyValue(K)=3.5m/s

(model02602);2.0m/s

(model02604);3.0m/s

(model02606).

Setup

1.Formodels

02602/02603/02604/02606/02609/02610/02611,

withserialnumberrange314000000–314999999

only:

Drilla6.4mm(1/4inch)diameterholeinthelower

handlebarofthemachine(PartNo.111-7260-03),360

mm(14.17inch)fromthebottomofthehandlebar

(Figure1).

Note:Ifthereisalreadyaholeatthislocationonthe

handlebar,nodrillingisrequired.

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3404-808*A

Summary of content (4 pages)

PAGE 1
Form No. 3404-808 Rev A Transport Wheel Kit HoverPro® 450/500/550 Machine Model No. 02622 Operator's Manual Safety Vibration • Before using this kit, refer to the machine Operator’s Measured vibration level for the left hand = 7.7 m/s2 (model 02602); 3.1 m/s2 (model 02604); 5.8 m/s2 (model 02606). Manual safety section. • Do not lift the machine onto the transport wheel kit or move the machine using the transport wheel kit while the engine is running.
PAGE 2
Operation 2. Attach the hook to one side of the lower handle bar using 1 hex bolt, 1 spacer, and 1 nyloc nut. Repeat for the other side (Figure 2). Note: When mowing, ensure that the transport wheel kit is secured to the lower handle bar with both hooks. Note: Refer to Figure 2 for the correct orientation of the bolts, spacers, and nuts. Use the transport wheel kit to safely transport the machine from one location to another. 3. Slide the axle spacer (300 mm) onto the axle (Figure 2). 4.
PAGE 3
2 3 4 1 4 2 3 1 5 7 6 5 9 8 6 12 14 12 11 13 10 13 g018538 8 9 10 Figure 2 1. Hex bolt (2) 5. Nut (2) 2. Hook (2) 6. Washer (2) 9. Axle spacer (25 mm) (2) 10. Wheel (2) 3. Spacer (2) 7. Undercarriage (1) 11. Axle spacer (300 mm) (1) 4. Nyloc nut (2) 8. Plain washer (4) 12. Washer (2) 3 13. Hex HD bolt (2) 14.
PAGE 4