USER GUIDE BLUETOOTH HEADSET MODEL: TP-BF02 THANK YOU FOR CHOOSING TZS BACKGROUND NOISE REDUCTION FOR CALLS
In the Box Headset Type-C Charging Cable Boom Mic User Guide 02 3.
Overview On/Off/Pairing Bluetooth LED Audio Input Answer/End call/ Mute/Unmute Rotate boom mic Internal mic Boom mic mute switch Boom microphone Previous track Play/Pause Next track Rotate to adjust volume Type C charging port 03
How to Wear 1. Insert the detachable Boom Microphone into the 2.5mm receptacle located on the headset. Mic receptacle Note: Please fully insert the boom microphone before use.
2. The boom microphone can move to accommodate a user’s preference for right side or left side wear. 3. Position the microphone to your preference.
Operation Power On Slide the switch to the CENTER position Power Off Slide the switch to the position 06
Connecting How to connect with the Bluetooth device. Bluetooth ON Bluetooth Devices TZS TP-BF02 Paired Now discoverable Slide the power switch to the “ “ position and hold until ‘pairing’ heard or the pairing LED flashes. Activate "Bluetooth" in your device‘s settings and select ”TZS TP-BF02”. indicate the headphone is connected, and ‘connected’ is heard.
Calls with a Smartphone Calls with a Smartphone 10m Press 1 × Answer Press 1 × End Call Press 2 × Decline Siri/Cortana/Assistance Press 2 × 08
Charging the Headset During charging the red LED will light. When fully charged, the LED will turn Plug the USB-C charging cable into a computer’s USB port. Plug the USB-C charging cable into a USB wall charger.
Other Operations Muting the Boom Mic: Depress and hold the button for 2 seconds. Muting the internal Mic: (When boom mic is not in use) Depress and hold the call key 2 seconds.
Battery Status: After the headset is powered on, press the call button briefly to hear the current battery status 100% -75%-50%-25%. Clearing the pairing: While the headset is powered on, press and hold the previous and next track buttons simultaneously for 10 seconds. A pink LED will light for 2 seconds and the headset will then enter pairing mode.
Product Specifications Bluetooth version: Bluetooth V5.0 Bluetooth Profile: A2DPv1.3.1; AVRCPv1.6; HFPv1.7; HSPv1.2; SPP v1.2; DID v1.3; HID v1.1; PXP v1.0.1; FMP v1.0; BAS v1.0 Working Frequency: 2.402GHz-2.
WARNING Headsets can deliver sounds at loud volumes and high-pitched tones. Avoid prolonged use of the headset at excessive sound pressure levels. Please read the safety guidelines below prior to using this headset. Safety information Use of a headset will impair your ability to hear other sounds. Use caution while using your headset when you are engaging in any activity that requires your full attention.
Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A product with a hot or cold battery may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures well below freezing. Battery warning! CAUTION – The battery used in this product may present a risk of fire or chemical burn if mistreated. Do not attempt to open the product or replace the battery. This will void the warranty.
Troubleshooting & Support Headphones will not power on: • Be sure the headphones are fully charged. • Remove “TZS TP-BF02” from your phone’s Bluetooth device list and try again. • If the model still does not appear, restart the headset and phone, then try again. After successfully pairing, the headphones disconnect • Be sure the battery has adequate power and recharge. • Headphones must be within 10m of most mobile devices.
There is no sound when listening to music • Increase the volume on your headphones or the mobile device. • Reestablish the Bluetooth wireless connection between the headphones and your mobile device. • Check if the audio app has paused or stopped playback. Headphones will not charge • Confirm that the charging cable is operational or undamaged. • Ensure that the USB charging cable is fully seated in the headphones and wall charger ports. • Confirm that the USB port is outputting power.
FCC Statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
