EVENT 2K SYSTEM / EVENT 4K SYSTEM
Important Safety Instructions 2
Table of Contents 1. INTRODUCTION 4 2. INSTALLATION TIPS 4 3. USEFULL DATA 4 4. QUICK START 5 5. CONNECT MANNER 6 6. BACK PANEL DESCRIPTION 8 7. DSP CONTROL 9 7. CONNECTION PLATE SYSTEM 13 8. WIRE CONNECTIONS 15 9. TECHNICAL SPECIFICATIONS 16 10. DSP SOFTWARE CONNECTION / IP CONTROL INSTRUCTION 18 10.
1 Introduction The new cabinets have been designed to provide a cost effective high grade solution while maintainig high quality cabinet construction and optimum components. Our Professional Audio Products are designed and tested by a highly qualified engineering team with more than 20 years of experience. Great care is placed in delivering products with excellent performance, specifications and dependable reliability.
Quick Start When mounting a speaker onto any stand, always ensure that the stand is on a flat, level sur-face, with the legs fully extended. Be sure to check that the maximum load weight for the stands is greater than the weight of the ARRAY SYSTEMS loudspeaker. Never use a stand with a maximum load weight lower than the speaker. Do not attempt to mout more than one speaker on a stand at one time. 4 The ARRAY SYSTEMS loudspeakers are heavy.
5 Connect Manner EVENT 2K 1. Turn the POLE/SAT-BM/SAT-TP back control switch to “LOCK” position. 2. Place the EVENT 2K on a flat surface and rotate the POLE/SAT-BM/SAT-TP from low to high into the bottom threaded bracket until it is tight. 3. After the installation is completed, if you choose to turn the control switch to the “UNLOCK” position, you can rotate the column to any angle. If you need to fix the angle, turn the control switch to the “LOCK” position. 4.
Connect Manner EVENT 4K 5 1. Place the EVENT 4K SUB on a flat surface. 2. Push the SAT from front to back into the SUB connector until it is tight. 3. After the installation is completed, if you need to disassemble, press the “LOCK” button of the SUB connector and push the SAT forward slowly.
6 Back Panel Description EVENT 2K / EVENT 4K (7) (9) (11) (12) (13) (10) (8) (14) (6) (5) (15) (16) (17) (4) (1) (2) (3) 1. AC INPUT-The AC connection is established via the IEC connector. The IEC connector is compatible with a lockout power cord (not included). 2. POWER - AC switch for turning the power on or off. When POWER is turned on,the power led lights up and LCD screen lights up. 3. MP3/BT PLAYER for option. 4. Convection fan. 5.
DSP Control With the integrated DSP control menu, users can select multiple DSP system settings on the speaker. 7 To access the DSP Control menu, follow below steps: 1. Press the MASTER VOL knob and the DSP Control menu will appear. Input Settings Factory Presets EQ User Programs System 2. Use the MASTER VOL knob to scroll through the menu items. Factory Presets EQ User Programs System Exit 3. Press the MASTER VOL knob to select the menu item you want to modify.
7 DSP Control MENU The Input Settings menu is used to configure the speaker's input sensitivity control and Delay and Phase control; Input Settings Input Settings Are you sure Switch to Mic ? No MIC Phase No Exit Yes Input Settings HI-Z MIC Delay: 0 Feet Phase Are you sure Switch to High Resistance ? Delay: 0 Feet Yes Input Settings MIC Input Settings HI-Z HI-Z Delay: 69.16 Feet Exit Phase Exit The MIC is used as the Input 1 input sensitivity control.
DSP Control The EQ menu is a 4-band EQ (equalizer) that the user can fine tune in addition to FUNCTION and LOCATION. 7 The options available for this selection are: HI, MD, LM, and LO. Back HI 12.1K Default: 0 decibels MD 2.52K Range: -18 decibels – +18 decibels LM 500.0 ALLBYPASS will be deleted, invalidating all set EQs. LO 101.5 FLAT is to restore all the adjusted EQ to factory settings. NOTE! The indoor equalizer (EQ) range shown is the factory default range for individual speakers.
7 DSP Control The Name menu is the name of the current speaker. This menu allows you to customize the name of the speaker as needed. The Default Settings menu is used to reset the speakers to their original factory settings. The options for this selection are: NO or YES. The Exit menu is used to return to the main interface. To reset your system to original factory settings, follow below steps: 1. From the System menu in the DSP menu, select Default Settings.
Connection Plate System Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down. 8 Two Active Subwoofers & Two Passive Satellite Speakers 1) Connect one side of the signal cable to the output of your mixer (left / right) with a TRS or XLR connector and the other side of the cable to the line input (combo) in the active subwoofer (with a TRS to XLR connector).
8 Connection Plate System Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down. 1) Connect one side of the signal cable at your audio mixer into output left / right (with Stereo-Jack or XLR) and the other side of the cable into the line input (Stereo-Jack) of your active speaker cabinet. 2) Connect the power cord to mains. 3) Turn on your mixer first, then the active speaker cabinets.
Wire Connections 9 15
10 Technical Specifications EVENT 2K SYSTEM: SUB+POLE+SAT-BM+SAT-TP EVENT 2K System Frequency Response Total Amplifier Power Maximum SPL@1M Crossover Frequency Dispersion(-6dB) Dimensions(WxHxD) Net Weight 40Hz – 20KHz (-10dB) 1000W Con�nuous/2000W Program/4000W Peak Class D @ 4 Ohms 128dB 220Hz 120°Horizontal 440 x 2015 x 640mm (17.32'' x 79.33'' x 25.20'') 37.81Kg (83.
Technical Specifications EVENT 4K SYSTEM: SUB+SAT EVENT 4K SYSTEM Frequency Response Total Amplifier Power Maximum SPL@1M Crossover Frequency Dispersion(-6dB) Dimensions(WxHxD) Net Weight 35Hz – 20KHz (-10dB) 2000W Con�nuous / 4000W Program / 8000W Peak Class D @ 4 Ohms 134dB 200Hz 130°Horizontal 460 x 2010 x 676mm (18.11'' x 79.13'' x 26.6'') 50.15Kg (110.
11 DSP software connection / IP Control instruction 1. List of required materials Computer（window system7-10）*1 Router*1 Network cable *1 CS PRO_1.09 software*1 EVENT 2K / EVENT 4K SYSTEM *1PCS 2. Connect the router to the module network port and turn on the power. 3. Make the computer connect to the router and open software “CS PRO_V1.0.9” EVENT 2K 5. Click the “Refresh”，and Click the “Device List” that appears. After the connection is OK, you can make initial debugging on this user page.
12 19
