User Manual

ManualsBrandsTOPGREENER ManualsElectricalTOPGREENER In-Wall PIR Sensor Switch, Occupancy Sensor Switch, Motion Sensor Switch, On/Off Override, 500W, Single Pole, NEUTRAL WIRE REQUIRED, White, TSOS5-W, 2 Pack

INSTALLATION INSTRUCTIONS

DESCRIPTION

WARNING

Turn the POWER OFF at the circuit breaker before installing the

sensor

Read and understand these instructions before installing. This device

is intended for installation in accordance with the National Electric Code

and local regulations. It is recommended that a qualified electrician

perform

s this installation. Make sure to turn off the circuit breaker or

fuse(s) and make sure power is off before wiring the device.

Use copper wires only.

WIRING DIRECTIONS

As illustrated in Figure 1, The TSOS5 has a 180° detection range with a

maximum distance of 30’ detection in front of the sensor and 15' on the

sides. For maximum results, the sensor must be properly installed between

the height of 4’ to 5’ and away from obstructions such as walls, furniture and

transparent barriers like Low-E glass.

The TSOS5 uses advanced passive infrared sensor to detect heat emitted

motion. The sensor switch can turn on a load and keep it on as long as it

detects motion. The sensor will automatically shut off the load at the end of the

selected time delay. The countdown of the selected time delay starts after the

last motion detected. The sensor is customizable with dials that can adjust

Time Delay, detection Range, and ambient Light Level.

1. Connect RED wire from sensor to the

LOAD wire.

Connect BLACK

wire from sensor to the HOT wire.

Connect GREEN wire from sensor to the GROUND wire.

Connect WHITE wire from sensor to the NEUTRAL wire.

ADJUSTMENT

TSOS5

OCCUPANCY SENSOR

SWITCH

Incandescent .......................................................................… 500W

Time Delay..........................................................…… 15Sec to 30Mins

Light Level.................................................................... 30 Lux--Daylight

Fluorescent..................................................................................500VA

Operation Temperature.................................................... 32°F--131 °F

Voltage .......................................................................... 120VAC,60Hz

Motor ...................................................................................…… 1/8Hp

COVERAGE

Figure 1

Max. 15'

on the sides

Max. 30'

from front

Installation

Height: 4' - 5'

Detection Range

The control panel is located behind the cover plate directly below the PIR

sensor. Pull from top corners of cover to uncover control dials (Figure 3).

LED Indicator

Mounting Yoke

Fresnel Lens

Figure 4

Figure 3

Neutral

White

Hot

Black

Ground

Green

Load

Red

Neutral

White

TSOS5

Illustrated in Figure 4, the control dials are used to adjust the following:

Time dial

This dial adjusts the time delay. Default position: 15 Seconds (Test mode)

Adjustable: from 15 Seconds to 30 Minutes (clockwise)

Range dial

This dial adjusts the detection range. Default position: Center at 65%

Adjustable: 30% (Position 1) to 100% (Position 4).

Note: Use the greater setting for larger coverage area.

Light dial

The sensor may be adjusted to operate at the desired level of ambient light.

• To do so, turn the dial to point the arrow toward the “-”sign for sensor to

detect motion and operate during low light or no light. Point the arrow

toward the “+”sign for sensor to operate when there’s more light in the

area or even during daylight.

TSOS5

SPECIFICATIONS

Figure 2

TSOS5

Switch Type........................................................................ Single Pole

Note: The white wire MUST be connected to the neutral wire in the junction box.

Please do not connect the white wire to any other wire besides the neutral.

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS TSOS5 OCCUPANCY SENSOR SWITCH ADJUSTMENT COVERAGE As illustrated in Figure 1, The TSOS5 has a 180° detection range with a maximum distance of 30’ detection in front of the sensor and 15' on the sides. For maximum results, the sensor must be properly installed between the height of 4’ to 5’ and away from obstructions such as walls, furniture and transparent barriers like Low-E glass. The control panel is located behind the cover plate directly below the PIR sensor.
PAGE 2
OPERATION The Load turns on when not desired: 1. Make sure there is no motion detected by the sensor. 2. Check for possible significant heat sources emitting within six feet (two meters) such as high wattage light bulbs, portable heaters or HAVC vents which may be triggering the sensor. 3. If the sensor is installed in a small room, turn the Range dial to a lower setting to avoid false or unwanted detection from a open window or door.