Manual
5.3 Operating environment
Do not place the product under any mechanical stress.
Protect the appliance from extreme temperatures, strong jolts, ammable gases, steam
and solvents.
5.4 Cable
Do not modify or repair cable components. Do not use damaged components.
Risk of death by electric shock!
Make sure that the cable is not squeezed, bent, damaged by sharp edges or put under
mechanical stress.
Avoid excessive thermal stress on the cable from extreme heat or cold.
Do not modify the cable. Otherwise the cable may be damaged. A damaged cable can
cause a deadly electric shock.
Do not touch the cable if it is damaged. If you notice damage, switch off the power genera-
tors and then disconnect the cable. Discard the cable. Do not use the cable again.
Ensure that the cable is not pinched, kinked or damaged by sharp edges.
Lay the cable so that nobody can trip over or become entangled in it to prevent injury.
5.5 Connections
Never make electrical connections if your hands are wet.
Making electrical connections on running generators can cause electric shock. Switch off
generators before connecting and disconnecting.
Loose connections can cause sparking and res. Make sure connections are secured be-
fore operating.
The cable is not designed to carry mains power. Never connect the cable to the mains
power supply.
5.6 Operation
Consult an expert when in doubt about the operation, safety or connection of the appliance.
Do not operate the parallel connection cable with only one generator. Always operate with
two generators.
Simultaneous use of the parallel connection and other outputs on the generator can dam-
age the generator. Do not use other outputs if you use the parallel connection.
5.7 Damaged components
If it is no longer possible to operate the product safely, take it out of operation and protect
it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation
can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
6 Product overview
1
2
3
4
1 Parallel connection cable
2 Overload reset button
3 Generator connectors
4 Industrial socket
7 Connection
7.1 Power generator combinations
The parallel connection cable supports the following generator combinations:
Generator 1 Generator 2
Option 1 QL2000i QL2000i
Option 2 QL2000i QL3500ig
Option 3 QL3500ig QL3500ig
Operating Instructions
32 A Parallel Connection Cable for
Power Generators
Item No. 2749813
1 Intended use
The product is a parallel connection cable. The cable is intended to combine the outputs of
two power generators into a single output to double the total power output. The cable is not
intended to be connected to the mains power supply.
The following limitations must be observed:
Maximum output current: 32 A
Must only be operated if connected to two generators
Only compatible with the Toolcraft power generator models:
– Toolcraft QL2000i (Item No. 2612921)
– Toolcraft QL3500ig (Item No. 2612922)
The parallel connection cable and the included industrial plug are protected against water in-
gress according to IPX4. Do not submerge the cable and plug in water.
The connectors by which the parallel cable is connected to the two power generators are not
protected against water ingress and must remain dry at all times.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, res, electric shocks or other hazards.
The product complies with the statutory national and European requirements. For safety and
approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product
available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights
reserved.
2 Delivery content
Parallel connection cable
Industrial plug
Operating instructions
3 Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
4 Description of symbols
The following symbols are on the product/appliance or are used in the text:
The symbol warns of hazards that can lead to personal injury.
The symbol warns of dangerous voltage that can lead to personal injury by electric
shock.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
5.1 General information
The device is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
If you have questions which remain unanswered by these operating instructions, contact
our technical support service or other technical personnel.
Maintenance, modications and repairs must only be completed by a technician or an au-
thorised repair centre.
5.2 Handling
Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.