Instructions

ManualsBrandsTOOLCRAFT ManualsCare ProductsTOOLCRAFT Mini grease gun 80 g without grease 1 pc(s)

Operating Elements

1 Coupler

2 Head assembly

3 Cylinder

4 Plate (internal)

5 End cap

6 Piston

Filling Instructions

• Unscrew the cylinder (3) from the

head assembly (2).

Check that the plate

(4) is all the way at the

bottom of the cylinder

(3). If needed, use a

screwdriver (or similar)

to push it down.

• Fill the cylinder (3) with grease

using your fingers or a spatula.

Wear gloves.

• Pack the grease by tamping the

end cap (5) against the palm of

your hand.

• Continue to add grease until the

cylinder (3) is full.

• Loosely attach the head

assembly (2), then insert a

screwdriver (or similar) into the

cut out in the end cap (5).

• Press the plate (4) into the

barrel to further pack the grease.

This helps prime the pump by

releasing trapped air pockets.

Stop pressing if grease

seeps out between the

head assembly (2) and

cylinder (3).

• Tighten the head assembly (2)

and wipe off any excess grease.

• Pump the piston (6) until grease

flows out of the coupler (1).

Troubleshooting

No grease is dispensed

• Air is trapped in grease. Loosen

the head assembly (2), press

plate (4) to remove air pockets,

then tighten the head.

• In cold temperatures, grease may

thicken or solidify and cannot pass

through the coupler (1). Refer to

the grease manufacturer operating

temperature information.

• Coupler (1) may get clogged with

debris, check for blockages.

Care and Cleaning

• Keep the outer body of the

grease gun dry, clean, and free

from grease.

• When not in use, store in a dry

location to inhibit rust.

• Do not use any aggressive

cleaning agents, rubbing alcohol

or other chemical solutions as

they can cause damage to the

housing and malfunctioning.

• Clean the product with a dry,

fibre-free cloth.

Disposal

At the end of its service

life, dispose of the

product in accordance

with applicable

regulatory guidelines.

You thus fulfill your statutory

obligations and contribute to the

protection of the environment.

Technical Data

Capacity ................... 80 cm

Pressure .................. 69 bar

1000 PSI

Coupler taper .......... 50°

Coupler tip ............... ø0.5 mm

Cylinder ................... ø40 mm

Dimensions .............. 120 x 146 x

40 mm

(W x H x D)

Weight ..................... 270 g (empty)

Operating Instructions

Grease Gun, 80 g

Item No. 1932032

Intended Use

This product is intended to be

used as a dispenser for loose

grease. The small coupler opening

increases precision.

For safety and approval purposes,

you must not rebuild and/or modify

this product. If you use the product

for purposes other than those

described above, the product may

be damaged. In addition, improper

use can result in other hazards.

Read the instructions carefully

and store them in a safe place.

Make this product available to

third parties only together with its

operating instructions.

This product complies with the

statutory national and European

requirements. All company names

and product names are trademarks

of their respective owners. All rights

reserved.

Delivery Content

• Grease gun

• Operating

instructions

Up-to-date

Operating Instructions

Download the latest operating

instructions at www.conrad.com/

downloads or scan the QR code

shown. Follow the instructions on

the website.

Safety Instructions

Read the operating instructions

carefully and especially

observe the safety information.

If you do not follow the safety

instructions and information on

proper handling in this manual,

we assume no liability for any

resulting personal injury or

damage to property. Such cases

will invalidate the warranty/

guarantee.

a) General Information

• The product is not a toy. Keep it out

of the reach of children and pets.

• Do not leave packaging material

lying around carelessly. This

may become dangerous playing

material for children.

• Protect the product from extreme

temperatures, direct sunlight,

strong jolts, high humidity,

moisture, flammable gases,

steam and solvents.

• Do not place the product under

any mechanical stress.

• If it is no longer possible to

operate the product safely, take

it out of operation and protect it

from any accidental use. Safe

operation can no longer be

guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended

periods in poor ambient

conditions or

- has been subjected to any

serious transport-related

stresses.

• Please handle the product

carefully. Jolts, impacts or a

fall even from a low height can

damage the product.

• Consult an expert when in doubt

about the operation, safety or

connection of the product.

• Maintenance, modifications and

repairs must only be completed

by a technician or an authorised

repair centre.

• If you have questions which

remain unanswered by these

operating instructions, contact

our technical support service or

other technical personnel.

b) Grease Gun

• Do not use near an open flame.

• Do not use with low viscocity oils

or greases. This may cause leaks.

• Read the grease manufacturer

warnings before use.

• Use clean grease.The grease

gun is not suitable for use in the

food industry.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240

Hirschau (www.conrad.com). All rights including translation reserved.

Reproduction by any method, e.g. photocopy, microfilming, or the capture in

electronic data processing systems require the prior written approval by the

editor. Reprinting, also in part, is prohibited. This publication represents the

technical status at the time of printing.