Instructions

Overhead View
b) Fix Arm to Base Mount
• Use a slotted head screwdriver to loosen the arm
pivot rod screw (5).
• Slide the arm pivot rod out (6).
• Attach the clamp arm (9) to the base mount (13).
You may need to adjust the position of the
base mount (13) on the rail to properly
align the cutting disc with the cutting
slot (16).
• For aligning the cutting tool, refer to section “f).
Alignment / Cutting Slot”.
c) Fix Extension Springs and Split Pins
d) Attach Spark Guard
Do not use the grinder without the spark guard (1) attached. The metal guard tted to the base
(17) is for the control of sparks only and not designed to prevent parts of the cutting disc from
causing injury. It should be positioned between the cutting disc and the operator.
• Attach the spark guard (1) as shown in “Operating Elements” using 2 x M6 Nuts, bolts and washers.
e) Mounting Angle Grinder
Always unplug the grinder before attaching it to the stand, during maintenance, when not in use
or before dismantling.
• Attach the head of the angle grinder using the supplied angle grinder attachment bolts (8), nuts and
washers as shown above.
• Use a slotted screwdriver to extend the alignment bolts (7) so the rubber tips are ush against the angle
grinder.
f) Alignment
Make sure the grinder is not connected to the power supply.
Cutting Disc
• Use a square tool to check that the cutting disc is perpendicular to the base (13) and parallel to the cutting
slot (16).
• If necessary adjust alignment bolts to adjust the angle of the cutting disc to the base.
Cutting Slot
• Gripping the grinder handle, slowly pull down, and check the position of cutting blade, it should dip into
the middle of cutting slot (16).
• If not properly aligned, loosen the scews holding the base mount (13) in position and slide it along the rail.
• If the rail does not provide enough scope for adjustment, you may need to completely remove the base
mount from the base (17) and attach to another mounting point.
• When proper alignment has been achieved, tighten all the bolts and screws.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1697807_v1_1018_02_dh_m_en(1)
g) Test Run
• Run the grinder for a few seconds then switch OFF and disconnect from power supply.
• Check that all screws, nuts and bolts are tight, and that the cutting disc is perfectly vertical.
• Make any adjustments if necessary.
Operation
Observe the safety and operating instructions of the angle grinder. Consult an expert when in
doubt about the operation, safety or connection of the device!
Always use the clamp to secure the work piece. Holding the work piece by hand or against the
body is unstable and can lead to loss of control and serious injury.
The product must be placed on a rm and level surface.
Check that all nuts, bolts and screws are tight before use, tighten if required.
Do not try to cut materials which are too large to be safely held by the clamp.
Allow the cutting disc to come to a complete stop before attempting to remove any material from
the clamp.
Risk of burn. Cutting material and drill may become hot. Wear protective gloves and allow to cool
down before touching.
a) Clamping Work Piece
Applying excessive force to pull up or push down on the clamp lever (2) may cause it to bend or
break.
• Rotate the clamp lever (2) anti-clockwise to loosen the clamp jaw (3).
• Loosen the clamp fence (4) if necessary, and adjust the cutting angle.
Refer to the angle indicator (15) for precise angles.
• Place the work piece between the clamp, check that the cutting point on the work piece is lined up with
the centre of the cutting slot (16).
• Tighten all bolts to set the angle and work piece for cutting.
b) Cutting.
• Switch the angle grinder on and gently pull the handle down to begin cutting the work piece.
• Always use the minimum amount of force needed to make the cut.
• Work patiently and apply the force evenly throughout the cut.
Care and Cleaning
• Let cool down if hot, then disconnect the angle grinder from the power supply before removing from the
stand.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
• Clean the product with a dry, bre-free cloth.
Care and Cleaning
• Let cool down if hot, then disconnect the angle grinder from the power supply before removing from stand.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
• Clean the product with a dry, bre-free cloth.
Technical Data
Supported cutting disc .......................... ø180 mm, 230 mm.
Cutting depth ........................................ Max. 18 mm
Dimensions (L x W x H) ........................300 x 290 x 345 mm
Weight ..................................................2950 g