User manual

Cleaning
Clean the surfaces of the retaining plates carefully; otherwise, they can cause scratches or
pressure marks on the plates to be carried. When carrying a fragile plate (e.g. glass), dirt on the
contact surfaces of the retaining plates leads to breakage of the plate!
Use only a clean, soft and dry cloth for cleaning.
Technical Data
Plate thickness .................................................... up to max. 25 mm
Load-carrying capacity per plate carrier .............. 80 kg
Dimensions .......................................................... 230 x 120 x 110 mm (L x W x H)
Weight ................................................................. 1 kg (per plate carrier)

OPERATING INSTRUCTIONS
Plate carrier
Item no. 47 85 00
Intended use
The plate carrier is used to easily carry large plates (glass panels, wooden boards, plaster
boards, etc.).
The safety instructions have to be followed without fail.
Any use other than that described above is not permitted and can damage the product.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• 2 plate carriers
• Transport case
• Operating Instructions
Safety Instructions

The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequential
damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
• For safety reasons, any unauthorised conversion and/or modifi cation to the product
is not permitted.
• The product is not a toy and it should be kept out of the reach of children.
• Always store the two plate carriers in the case provided.
• When carrying plates, always use suitable protective equipment (e.g. safety shoes,
gloves, etc.).
• Before carrying plates of fragile material (e.g. glass), the contact surfaces of the
retaining plates of the two plate carriers are to be checked carefully for impurities
and then cleaned, if necessary. Otherwise, the pressure force while the plate is
being carried leads to breakage or damage to the plate! Risk of injury!
• For use in commercial institutions, the accident prevention regulations of the em-
ployer’s liability insurance company are to be observed.
• In schools, educational centres, hobby and self-help workshops, the use of the
product is to be supervised by trained employees.
• Do not leave packaging material carelessly lying around since it could become a
dangerous plaything for children.
• If you are in doubt about how to use the device correctly, or have any questions
not covered by these operating instructions, please contact our technical support or
another specialist.
Operation
• Fold the grip of the plate carrier in the middle.
• Place the plate carriers on the sides of the plate to be carried; this must be dry, otherwise the
moisture can cause the plate to slip out - injury hazard!
• Fold the grip of the plate carrier upward so that both retaining plates lie fi rmly against the plate.
• The retaining plates are pressed against the plate to be carried by lifting or carrying the plate.
Keep the weight of the plate mainly in the middle of the plate carrier, otherwise the plate may
slip out of the plate carrier!
Carry the plate as upright as possible.
Depending on the material quality and weight of the plate, the transport of the plate can lead
to pressure marks. This applies especially if the plate is not made of solid material.
• After you set down the plate, fold the grip of the plate carrier downward a little; the plate carrier
can now be removed again. In doing so, hold the plate fi rmly; otherwise it will tip over.
• When the plate carrier is no longer needed, store it in the carrying case provided.
Version 07/12
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.