INDEX 1 INTRODUCTION 2 2 POWER UNIT CHARACTERISTICS 5 3 CHARACTERISTICS OF FLEXIBLE SHAFT AND POKERS 5 4 GENERAL AND SPECIFIC SAFETY RULES 6 4.1 WORK AREA 6 4.2 PERSONAL SAFETY 6 4.3 TOOL USE AND CARE 6 4.4 SERVICE 6 4.5 SPECIFIC SAFETY RULES 6 5 USAGE CONDITIONS 7 6 OPERATION AND MAINTENANCE 7 6.1 BEFORE START 8 6.2 GETTING STARTED 8 6.3 SHAFT CONECTION TO POWER UNIT 8 6.4 POKER CONNECTION TO FLEXIBLE SHAFT 6.
1 INTRODUCTION Thank you for trusting the Tomahawk brand. For the maximum performance of the equipment, we recommend to read carefully the safety recommendations, maintenance, and usage listed in this manual Defective parts should be replaced immediately to avoid major problems. The effective longevity of the equipment will increase if the manual instructions are followed. We will glad to help you with any comments or suggestions in reference to our equipment. Quick Start Instructions. 1. Remove 2.
3. Add 10W-30 or 10W-40 Oil to Honda Engine. 4. Attach Vibrator Shaft to Vibrator Power Unit. 5. Make Sure engine kill switch is ON located near thumb.
6. Prime Engine, Set Choke to (up position), Pull Recoil Starter. 7. Once engine fires set choke to closed (down position). 8. Use thumb to adjust speed of engine and vibration speed.
2 POWER UNIT CHARACTERISTICS HONDA GX-35 BACKPACK VIB-BAR MODEL TYPE/DISPLACEMENT MAX OUTPUT/R.P.M. CARBURETTOR IGNITION STARTING FUEL FUEL TANK CAPACITY 4 STROKE / 35.8 CC 1.6 HP / 7000 RPM DIAPHRAGM TYPE TRANSISTORS MAGNETO COIL 89 Octane Gas 700 CC 7lbs (WITHOUT WEIGHT CLUTCH) SPEED. .......................................................... 9,000 - 10,000 RPM WEIGHT. ........................................................ 15lbs (BACKPACK) FUNCTION. ................................................
en NUT TO CONNECT TO THE MOTOR LEFT THREADS HOSE END REINFORCEMENT 1''-2'' DIAM. HOSE HEX. DRIVER LEFT THREADS 4 GENERAL AND SPECIFIC SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. 4.1 WORK AREA KEEP your work area clean and well lit. Cluttered benches and dark areas invite accidents. DO NOT OPERATE power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
4.5 SPECIFIC SAFETY RULES For your own safety, as well as for the others one, and in order not to cause any damage to this equipment, please read carefully the instructions that are explained as follows: 1.- For the proper use of this device, please assure that the operator has been correctly informed of the content of this manual before using it. 2.- This machine must be used only under the applications for which it has been designed and according to these safety instructions. 3.
6.7.8.9.- Check the oil reservoir of the motor is full (see engine manual) in the 4-stroke engine (SAE10W40). Check all the bolts are well tightened. Start the motor, regulate the speed with the accelerator until it reaches a good vibration. When a defect or a malfunction has been detected, endangering the use of this machine or not, stop the work and make the correspondent maintenance to avoid any danger or bigger damage. 6.2 GETTING STARTED Read item 5 USAGE CONDITIONS 6.
7 DIMENSIONS OF WEAR FOR DIAMETERS AND LENGTHS OF THE POKERS MODEL DIAMETER (inch) LENGTH (inch) TVIBH 1-2 12 A. B. C. D. The minimum dimensions are bold printed. The dimensions into brackets are the original dimensions. Replace the housing when reach the minimum diameter. Replace the tip when reach the minimum length. 8 PERIODIC MANTENANCE 8.1 PERIODIC MAINTENANCE OF THE PETROL ENGINE 1.- Daily (8 hours).
of the shaft, The recommended quantity is 25 g per meter. Do not overlubricate, it could cause the grease penetrate into the poker, Do not clean the shaft with solvent. The grease recommended is of the brand KLÜBER LUBRICATION with the following characteristics: Dropping point s/ DIN 51801/1 (ºF) .................................................. >220 Temperature range (ºF) .................................................................... 86 a 266 Maximum temperature during a short time (ºF) ............
9.2 LOCATING MALFUNCTIONS OF FLEXIBLE SHAFT AND POCKERS PROBLEM CAUSE/SOLUTION The motor works overload 1.- Head is overlubricated. and overheats 2.- Too much grease in shaft or too little. 3.- Failure of seal and the transmission grease have gone into the head or the head oil have gone out. 4.- Head movement is restricted. 5.- Transmission with extreme bents. 6.- Transmission in bad condition, broken hose. Bearing failure 1.- Not enough oil in the head. 2.
11 RECOMENDATIONS OF USE OF CONCRETE VIBRATOR 1. Choose the type of vibrator adequate to the dimensions of the structure to vibrate, the distance among the reinforcement and the slump cone. It is recommendable to have an additional concrete vibrator. 2. Before starting check that the concrete vibrator is in good use and it works correctly. Use the means of safety and protection. 3. Pour the concrete in the structure avoiding high heights. Try to pour levelled the concrete.
2020 CATALOG GENERATORS FINISHING COMPACTION PRODUCT 3,550 lbs/ft Vibratory Rammer 3,400 lbs/ft Plate Compactor 3,000 lbs/ft Plate Compactor 3.6 HP Honda GXR120 Engine Easily achieve a 100% compaction rating 3-in-One Fuel System with carburetor protection 13” x 11” plate for narrow trenches and corners 3 Year Engine Warranty & 1 Year Product Warranty 5.5 HP Honda GX160 Engine Easily achieve a 100% compaction rating 22” x 20” cold, rolled steel beveled base plate Includes 3.
USE CODE SAVE10 AT CHECKOUT FOR 10% OFF AND MORE PEST CONTROL WELDING / POWER YOUR NEXT ORDER* INVERTER SERIES INVERTER SERIES 120 Amp Portable Welder Generator 210 Amp Portable Welder Generator 7500 & 9000 Watt Generators Steady 120 Amp DC welding output 60% Duty Cycle for extended use Suitable for welding rods from 6010 to 6013 Includes wheel kit for job site portability 2 Year Product Warranty Steady 50 - 210 Amp DC welding output 60% Duty Cycle for extended use Suitable for welding rods from
Power Your World Tomahawk understands to keep a job-site running smoothly the proper equipment and spare parts are needed at the drop of a hat. With same day shipping and faster delivery times, count on Tomahawk to keep you powered throughout the day! With long lasting parts and engines, Tomahawk equipment will be the star of your fleet for years to come. Visit www.tomahawk-power.com to get started today! Tomahawk Power, LLC San Diego, CA Sales Support (866) 577-4476 sales@tomahawk-power.com www.
