TOS38 38” PUSH SWEEPER Operation Manual
Table of Contents About these Instructions 3 Safety Instructions 3 Instructions for Use 5 Assembly 6 Operation 7 Maintenance and Troubleshooting 9 Specifications 11 Warranty 11 2 / 12
I. About These Instructions 1.1 Technical further development We are continuously working on further development of all our products. We therefore reserve the right to make changes in the scope of delivery with respect to form, technology, and equipment. No claims can therefore be derived from information and illustrations contained in these instructions. 1.2 Target group These instructions are intended for the person using this sweeper.
The user of the sweeper is responsible for injuries and damage that are caused due to non-compliance with these instructions. 2.1 Intended use This sweeper is designed in accordance with the state of the art and recognized safety regulations. Nevertheless, use of the sweeper can lead to dangers for the user or third parties or damage to the sweeper and other material assets. The sweeper is intended for commercial use, e.g.
Observe all safety and danger instructions on the sweeper. The user must ensure the presence and legibility of all warning and information notices throughout the entire service life of the sweeper. Use only genuine spare parts and accessories that have been approved by the manufacturer. These guarantee that the machine can be operated safely and without faults.
6 / 12
V. Operation 1. The operator should use the sweeper under normal operation and consider the surrounding environment when operating; be cautious of people around the sweeper and objects that may unintentionally sweep in an outward direction. 2. Depending upon the service the operator intends to sweep you can adjust the best height of the front and back brushes. The higher the brushes the less pressure on the surface. A higher brush may be less effective but will increase the longevity of the brush.
1.The front brush is fastened with three screws 2. Main Brush Adjusting Handle “+” main brush down “ - ” main brush up 3. Front Brush Adjusting Handle “+” main brush down “ - ” main brush up 1. No more than 19 cm across the steps when machine back up 2. Three angle adjustments for handle 3. The height difference of cleaning ground not exceeding 2.
1. Hold your handle and lift it up to remove the garbage can 2. When the main brush is entangled with garbage, it should be reversed and removed in time. 3. Dump the garbage along the side of the garbage can. No knocking on the garbage can is allowed. VI. Maintenance and Troubleshooting Cleaning the machine -Always clean, dust off and clear debris from the sweeper -Do not use any grease solvents, pressure washer for cleaning the sweeper. -Wear safety gear when cleaning to reduce the risk of injury.
Problem: Side Brush not moving Solution: Replace Brush and or band that rotates brush. Problem: Debris Not sweeping up into hopper. Solution: Replace roller Brush Problem: Brush Bristles Damaged Solution: Use a heat gun or blower dry to straighten bristles Problem: The machine is difficult to push Solution: The Roller brush may have a blockage. Unclog the brush. Also, the side brushes may be a setting that is too low; increase the height of the brushes. Problem: Gear components Stiff.
VII. Specifications Sweeping performance: Trash Bin Hopper Capacity: 14.5 Gallon Sweeping Distance: 31-38’’ Brush Assembly Types: 2 side brushes 1 roller brush Weight: 60lbs Dimensions: 47” x 31” x 37’’ Uses: indoor and outdoor Fine dust filter: included Adjustable roller brush: yes Foldable side brush: yes VIII. Warranty • The relevant national regulations apply in each country. Excepted from this are wearing parts such as sweeping lip, angled wheels and running wheels.
COMPACTION FINISHING GENERATORS 3,550 lbs/ft Vibratory Rammer 3,400 lbs/ft Plate Compactor 3,000 lbs/ft Plate Compactor 3.6 HP Honda GXR120 Engine Easily achieve a 100% compaction rating 3-in-One Fuel System with carburetor protection 13” x 11” plate for narrow trenches and corners 3 Year Engine Warranty & 1 Year Product Warranty 5.5 HP Honda GX160 Engine Easily achieve a 100% compaction rating 22” x 20” cold, rolled steel beveled base plate Includes 3.
WELDING / POWER PEST CONTROL AND MORE INVERTER SERIES INVERTER SERIES 120 Amp Portable Welder Generator 210 Amp Portable Welder Generator 9000 Watt Generators Steady 120 Amp DC welding output 60% Duty Cycle for extended use Suitable for welding rods from 6010 to 6013 Includes wheel kit for job site portability 2 Year Product Warranty Steady 50 - 210 Amp DC welding output 60% Duty Cycle for extended use Suitable for welding rods from 6010 to 7024 Electric Key Start with battery included 2 Year Product
Power Your World Tomahawk understands to keep a job-site running smoothly the proper equipment and spare parts are needed at the drop of a hat. With same day shipping and faster delivery times, count on Tomahawk to keep you powered throughout the day! With long lasting parts and engines, Tomahawk equipment will be the star of your fleet for years to come. Visit www.tomahawk-power.com to get started today! Tomahawk Power, LLC San Diego, CA Sales Support (866) 577-4476 sales@tomahawk-power.
