Operation Manual

16 17
For better reception
• For FM, pull out the telescopic antenna. Incline and turn the antenna. Reduce
its length if the signal is too strong (very close to a transmitter).
• For AM the set is provided with a built-in antenna so the telescopic antenna is
not needed. Direct the antenna by turning the whole set.
CD Disc Section
Playing a Disc
1. Open the CD door.
2. Hold the disc with the label side facing up and press it onto the spindle until it
clicks into place
3. Slide the Function selector to the “CD/ MP3/ USB” position. The disc will rotate
for a few seconds, the total number of tracks will be indicated on the LED
display. Adjust the volume as desired.
4. Press PLAY/PAUSE button to start playing.
5. Press the PLAY/PAUSE again to stop playing temporarily. The PLAY indicator
will begin to flash. Resume normal play by pressing the PLAY/PAUSE button
again.
6. To stop playback, press the STOP button .The total number of tracks will be
shown on the display.
TRACK SEARCH
Press the F.FWD button to skip to the next track on the disc.
Press the REW button skip to previous track.
FORWARD/REVESE SEARCH
Press and hold the F.FWD or REW button during play to scan the disc at high
speed.
When the desired section of the disc if found, release the Button and normal play
will resume.
F.FWD -------------------Forward
REW --------------------Backward
Press and hold the F.FWD button while playing to scan the current track forward
at high speed.
Press and hold the REW button while playing to scan the current track backward
at high speed.
POWER SUPPLY
Operate by DC
Batteries (not included)
Open the battery compartment and insert eight batteries, UM-2 or C-cells,
(preferably Alkaline) with the correct polarity as indicated by the “+” and “–”
symbols inside the compartment.
Incorrect use of batteries can cause electrolyte leakage and will corrode the
compartment or cause the batteries to burst. Therefore:
• Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of
the same type for the set.
• When inserting new batteries, do not try to mix old batteries with the new
ones.
• Remove the batteries if the set is not to be used for a long time.
Unit power supply (mains AC 230V/50Hz)
1. Check if the power voltage, as shown on the type plate located on the bottom
of the set, corresponds to your local AC power supply.
2. Connect the power cord to the AC MAINS inlet and the wall outlet. The power
supply is now connected and ready for use.
3. To switch off completely, unplug the power cord from the wall outlet.
Basic Function
Switching power POWER OFF/AUX/RADIO/CD/ MP3/ USB to save energy
Whether you are using mains or battery supply, to avoid unnecessary energy
consumption always adjust the Function selector to POWER OFF.
General operation
1. To select your sound source adjust the Function selector to POWER OFF/
AUX/RADIO/CD/ MP3/ USB
2. Adjust the sound with the VOLUME knob.
3. To switch off the set, adjust the Function selector to POWER OFF position.
RADIO OPERATION
Radio reception
1. Slide the POWER OFF/AUX/RADIO/CD/ MP3/ USB selector to RADIO.
2. Slide the BAND selector to a desired setting – AM/FM MONO/FM ST
3. Rotate the TUNING control to find the desired stations.
NOTE: If the BAND selector is set to the FM stereo position and once you
have tuned to an FM stereo station, the FM stereo LED indicator will light.
When the FM stereo station signal is weak, slide the AM/FM MONO/FM ST
Band selector to FM MONO.
4. When you have finished listening, slide the POWER OFF/AUX/RADIO/CD MP3
selector to the POWER OFF position to shut the power off.
LRL-1913 Manual.indd Sec2:16-Sec2:17LRL-1913 Manual.indd Sec2:16-Sec2:17 7/29/10 10:12:10 AM7/29/10 10:12:10 AM