User's Manual
Table Of Contents
- Tobii I-Series User’s manual v_1_0_4 - en-US_WEBHQ_102.6.11
- 1 Introduction
- 2 Safety
- 3 Overview of the Tobii I–12 and I–15
- 4 Batteries in the Tobii I-Series
- 5 Using the Tobii I-Series
- 5.1 Starting the Device
- 5.2 Shutting Down the Device
- 5.3 Using Tobii Gaze Interaction
- 5.4 Using Windows Control
- 5.5 Wake the I-Series from Sleep with Gaze Interaction
- 5.6 Pause/Resume Gaze Interaction and Put the I-Series to Sleep with Gaze Interaction
- 5.7 Using the Cameras
- 5.8 Using the GEWA Programmable IR Remote Control
- 5.9 Adjusting the Volume
- 5.10 Adjusting the Sound
- 5.11 Performing a Factory Recovery
- 5.12 Calibrating the Touch Screen
- 6 Configuring the I-Series with the I-Series Control Center
- 7 Tobii Gaze Interaction Settings
- 8 Gaze Selection Settings
- 9 Product Care
- Appendix A Support, Warranty, Training Resources
- Appendix B Compliance Information
- Appendix C Computer Device States of Operation
- Appendix D Maximum Allowed Temperature
- Appendix E Technical Specifications
- Appendix F Approved Accessories
For more information and for how to configure the System Off-Screen menu, see
7.6.1 System Off-Screen Menu, page
56
.
3. Selecting, using Gaze Interaction, the
(Pause) icon that pops up.
To Sleep-on-Gaze:
1. Make sure the SSlleeeepp--oonn--GGaazzee System Off-Screen menu is activated, see
7.6.1 System Off-Screen Menu, page 56
2. Look at the area where the System Off-Screen menu has been configured for your I-Series, see
Figure 5.8 System Off-
Screen Area, page 29
For more information and for how to configure the System Off-Screen menu, see
7.6.1 System Off-Screen Menu, page
56
.
3. Selecting, using Gaze Interaction, the
(Sleep-on-Gaze) icon that pops up.
4. Select YYeess for Sleep or NNoo for Cancel
5.7 Using the Cameras
The two built-in cameras allows you to take snapshots of items in front of the I-Series device and also from the display side.
Use TToobbiiii CCoommmmuunniiccaattoorr or other relevant software to operate the cameras.
5.8 Using the GEWA Programmable IR Remote Control
The I-Series device includes a GEWA Programmable IR Remote Control — Environmental Control Unit (ECU) with two (2) filter
windows:
• 1 Transmitter filter window — Position 6 in
Figure 3.1 Front and Back, page 9
• 1 Transmitter and Receiver filter window — Position 27 in
Figure 3.2 Bottom, Left and Right Side, page 10
Use the Transmitter and Receiver filter window (position 27 in
Figure 3.2 Bottom, Left and Right Side, page 10
) when
programming the GEWA Programmable IR Remote Control in TToobbiiii CCoommmmuunniiccaattoorr.
The GEWA Programmable IR Remote Control is a programmable Infrared device that can be used to control equipment with an
IR Remote Control such as TV-sets or DVDs.
For more information about how to use and program the GEWA Programmable IR Remote Control, see GGeettttiinngg SSttaarrtteedd wwiitthh
EEsssseennttiiaallss ffoorr CCoommmmuunniiccaattoorr 44.
If the device you are trying to control is not responding, try tilting the I-Series device up or down slightly to change the
angle at which the IR signal is being sent.
The ECU is not to be relied on as the only method of interaction with IR controlled devices.
5.8.1 Handling Tobii Product Key
To use the GEWA Programmable IR Remote Control, a Tobii Product Key is required. To view or enter a Tobii Product Key, go
to the Tobii Product Key section in the II--SSeerriieess CCoonnttrrooll CCeenntteerr. See
6.7 Tobii Product Key, page 41
When the Tobii Product Key is in place, the GEWA IR Programmable Remote Control is ready to use.
5.9 Adjusting the Volume
To adjust the volume use the Volume Up button (Position 11) and volume down button (Position 12) on right hand side of the
I-Series device. For position references, see
Figure 3.2 Bottom, Left and Right Side, page 10
Volume adjustments can also be done in TToobbiiii CCoommmmuunniiccaattoorr.
30
5 Using the Tobii I-Series
Tobii I-Series User’s manual v.1.0.4 - en-US