User's Manual
Table Of Contents
- 1 Introduction
- 2 Safety
- 3 Overview of the Tobii Dynavox I–12+ and I–15+
- 4 Batteries in the Tobii Dynavox I-Series+
- 5 Using the Tobii Dynavox I-Series+
- 5.1 Starting the Device
- 5.2 Shutting Down the Device
- 5.3 Using Gaze Interaction
- 5.4 Using Windows Control
- 5.5 Wake the Tobii Dynavox I-Series+ from Sleep with Gaze Interaction
- 5.6 Pause/Resume Gaze Interaction and Put the Tobii Dynavox I-Series+ to Sleep with Gaze Interaction
- 5.7 Using the Cameras
- 5.8 Using the GEWA Programmable IR Remote Control
- 5.9 Adjusting the Volume
- 5.10 Adjusting the Sound
- 5.11 Performing a Factory Recovery
- 5.12 Calibrating the Touch Screen
- 6 Configuring the Tobii Dynavox I-Series+ with the I-Series Control Center
- 7 Gaze Interaction Settings
- 8 Gaze Selection Settings
- 9 Product Care
- Appendix A Support, Warranty, Training Resources
- Appendix B Compliance Information
- Appendix C Computer Device States of Operation
- Appendix D Maximum Allowed Temperature
- Appendix E Technical Specifications
- Appendix F Approved Accessories
5.9 Adjusting the Volume
To adjust the volume use the Volume Up button (Position 11) and volume down button (Position 12) on right hand side of the
Tobii Dynavox I-Series+ device. For position references, see Figure 3.2 Bottom, Left and Right Side, page 17
Volume adjustments can also be done in Tobii Dynavox Communicator /Tobii DynaVox Compass.
5.10 Adjusting the Sound
You can configure the built-in speakers using the Windows 8.1Control Panel > Sound.
We refer to Microsoft’s information on how to configure the sound in the Windows 8.1Control Panel.
Sound adjustments can also be done in Tobii Dynavox Communicator /Tobii DynaVox Compass.
5.11 Performing a Factory Recovery
Every Tobii Dynavox I-Series+ device has a factory image stored on the disk. If you need to restore the device back to its original
state, this can be done by using our OEM Factory Recovery Application.
This will delete any personal data or software installed after the device was delivered.
Factory Recovery means that the device will be reset to the factory mode, without anything installed. In this mode you have to
re-enter your Tobii Dynavox Product Key and licenses to perform the SW installation you have ordered.
Make sure you’ve connected the Power Supply before you start the process - do not run the device on batteries, as it
might run out of power during the Factory Recovery. In such a scenario, you might have to send the unit back to
Tobii Dynavox for repair.
To perform a Factory Recovery for your Tobii Dynavox I-Series+ device, follow this procedure:
1. Backup your personal data such as documents and Tobii Dynavox Communicator /Tobii DynaVox Compass settings
etc.
2. Make sure you have the Tobii Dynavox I-Series+ Product Key available
3. Shut down the device
4. Connect a keyboard
5. Start up device again
6. Hold down the
(Arrow Down) keyboard button continually during startup until you get into “Windows Boot
Manager”
7. Select "Factory Reset” and press the
(Enter) keyboard button.
8. The Tobii Dynavox I-Series+ Software Installation dialogue will be loaded
9. Follow the instructions on the screen. These steps are identical to the initial setup you did when you first received the
device.
or
To perform a Factory Recovery for your Tobii Dynavox I-Series+ device, follow this procedure:
1. Backup your personal data such as documents and Tobii Dynavox Communicator /Tobii DynaVox Compass settings
etc.
44
5 Using the Tobii Dynavox I-Series+
Tobii Dynavox I-Series+ User’s manual v.1.0 - en-US