INSTRUCTION MANUAL Digital Wireless Microphone WM-D5200 Thank you for purchasing TOA’s Digital Wireless Microphone. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
TABLE OF CONTENTS 1. SAFETY PRECAUTIONS .......................................................................................................... 3 2. GENERAL DESCRIPTION ........................................................................................................ 5 3. FEATURES .................................................................................................................................. 5 4. HANDLING PRECAUTIONS ................................................................
1. SAFETY PRECAUTIONS • Before use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety. • After reading, keep this manual handy for future reference. WARNING Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device operates on a no-protection, no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required.
2. GENERAL DESCRIPTION The WM-D5200 is a digital wireless microphone employing a condenser microphone element that features high sensitivity and clear sound quality. The microphone is specially designed to be used in conjunction with TOA's WT-D5800 digital wireless receiver. 3. FEATURES • Employs the PLL-synthesizer system. • TOA's unique digital audio processing technology ensures high quality sound.
5. NOMENCLATURE AND FUNCTIONS [Front] 1. Power switch [ON/OFF] Power can be turned on by sliding the power switch to the ON position, while it can be turned off by sliding it back to the OFF position. 2 ON OFF 1 3 6 2. Battery checker (green/orange/red) Lit: Power ON Unlit: Power OFF* The remaining battery power is represented by the color of the indicator. Green: Battery power is at full charge. Orange: Battery power depletion has started.
[Battery case internals – front] 6 7 8 9 4 ON 5 [Battery case internals – side] 12 OFF H L 10 11 4. Bank selector switch Make sure that the microphone is identical to the wireless receiver in the bank number. 8. Encryption setting switch 9. Code setting switch [0 – 9] 5. Channel selector switch Make sure that the microphone is identical to the wireless receiver in the channel number. 10. Transmission output changeover switch [H/L] H: 10 mW L: 1 mW 6. Maintenance port Not used.
6. PREPARING BATTERIES The WM-D5200 can operate on both the optional rechargeable battery or replaceable dry batteries. Please carefully read the corresponding sections for correct use. 6.1. Battery Insertion Step 1. Turn off the power switch. Step 2. Hold the microphone body and rotate the battery compartment cover counterclockwise to remove it. Step 3. Insert an AA battery according to (+) and (–) indications on the battery compartment.
6.3. When Operating on Rechargeable Battery CAUTION Do not charge the unit with an alkaline dry battery installed. Charge the dedicated rechargeable battery*. Failure to observe these instructions could cause fire or personal injury due to a bursting battery. * The optional TOA WB-2000-2 (package of 2). Notes • When operating on rechargeable batteries, the optional BC-2000 Battery charger is required.
7. OPERATION Step 1. Confirm that the wireless microphone and the wireless receiver are identical in the bank and channel numbers If not identical, turn the power switch to the OFF position, then set the bank and channel numbers to the same ones as the receiver. Step 2. Turn the Power switch to the ON position. Then, confirm the battery checker will light green or orange. Step 3. Turn the Power switch to the OFF position after use. 8. Function SETTINGS 8.1. Setting the Bank and Channel Numbers Step 1.
8.2. Performing Encryption Settings To enhance security, the WM-D5200 is provided with an encryption setting function that prevents leakage of transmitted information. This function also has the advantage of eliminating radio interference if enabled. Before enabling the encryption setting, be sure that bank and channel settings are completed first. Tip In addition to the WM-D5200, the WT-D5800 Digital Wireless Receiver also requires setup.
8.2.2. Performing encryption settings [Switching the Encryption function from OFF to ON] See also the instruction manual enclosed with the WT-D5800 receiver. Step 1. Enable the receiver's encryption function. Step 2. With the battery compartment cover removed, switch ON the microphone power switch and confirm that the Encryption indicator is unlit. If the indicator is lit, switch encryption from ON to OFF (see p. 13). Unlit Step 3. Switch OFF the microphone power switch. Step 4.
[Switching the Encryption function from ON to OFF] Step 1. With the battery compartment cover removed, switch ON the microphone power switch and confirm that the Encryption indicator is lit. Lit Step 2. Switch OFF the power switch. Step 3. Switch ON the microphone power switch while holding down the Encryption setting switch. Note Do not switch OFF the microphone power switch during setting. Step 4. Confirm that the Encryption indicator has extinguished, then release the Encryption setting switch.
8.3. Performing Code Settings (When Encryption Function Is OFF) 8.3.1. Code Setting Summary By presetting the specified code between the wireless microphone and receiver, audio is only output when a digital signal received from the wireless microphone has the same ID code as the receiver. Even if another signal is received from an adjacent area, if the code does not match, audio is not output. Ten varieties of code can be selected ([0] – [9]) for appropriate use, depending on circumstances. 8.3.2.
8.4. Performing Transmission Output Changeover Switch Settings Transmission can be set for either of two outputs: ‘H’ (10 mW) or ‘L’ (1 mW). The switch is factory-preset to the ‘H’ position. Note Be sure to turn the microphone’s power switch OFF before performing settings. Step 1. Confirm that the power switch is turned OFF, then remove the battery compartment cover and battery. 1 1 Step 2. Using the supplied screwdriver, set the changeover switch to the desired transmission output.
9. CONVENIENT FUNCTIONS (Microphone Sensitivity Selector Switch Settings) Microphone sensitivity can be set to "0 dB" (H) or "–10 dB" (L). Notes • Switch OFF the power switch when selecting the sensitivity. • When the sensitivity is set to "H," avoid positioning the microphone too close to the mouth and speaking in a loud voice, as the sound could become muddled and difficult to understand. Step 1. Confirm that the power switch has been switched off, then remove the battery compartment cover. 1 Step 2.
10. Specifications Microphone Element Electret condenser unit: Unidirectional Frequency Range 576 – 606 MHz for USA/Canada Modulation type Channel Selectable RF Carrier Power Maximum Input Level Audio Frequency Response FSK 160 channels (The number of channels may differ from country to country.
Number of DoC: 16113001 DECLARATION OF CONFORMITY We: TOA Electronics Europe GmbH Süderstraße 282, 20537 Hamburg, Germany as the authorised representative of the Manufacturer: TOA Corporation 7-2-1, Minatojima-nakamachi, Chuo-ku, Kobe, Japan 650-0046 declare, under our sole responsibility, that the product Product Name: DIGITAL WIRELESS MICROPHONE Model Number: WM-D5200 conforms with following specifications: EMC: ETSI EN 301 489-1: V1.9.2 (2011-09), ETSI EN 301 489-9: V1.4.
COMPLIANCE STATEMENT TO WM-D5200 AT DE Österreich Deutschland België BE Belgique CH Schweiz DK Danmark ES España FI Suomi / Finland FR CH France Suisse GB Greate Britain GR Ελλαδα IT CH Italia Svizzera NL Nederland NO Norway Hiermit erklärt TOA Electronics Europe GmbH die Übereinstimmung des Funkmikrofon mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.
PT Portugal SE Sverige 20 TOA Electronics Europe GmbH declara que este Microfone Emissor está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Härmed intygar TOA Electronics Europe GmbH att denna Trådlös mikrofon står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Intended use of WM-D5200 Der Gebrauch dieses Funkmikrofons für andere Zwecke als zur Übertragung eines Tonsignals an einen passenden Funkempfänger ist nicht zulässig. AT CH DE Österreich Schweiz Deutschland WICHTIGER HINWEIS ! Dieses Gerät arbeitet auf in der europäischen Gemeinschaft (EU) nicht harmonisierten Frequenzen. Abhängig vom geografischen Gebiet dürfen nur bestimmte Frequenzen legal mit oder ohne Autorisierung/individueller Lizenz entsprechend der beigefügten Frequenztabelle genutzt werden.
Es ilegal utilizar este micrófono inalámbrico para cualquier otro propósito que no sea transmitir una señal de audio a su correspondiente receptor o módulo sintonizador. ES España ¡ AVISO IMPORTANTE ! FI Suomi / Finland HUOMIOITAVAA ! GB IE Greate Britain Eire IMPORTANT NOTICE ! This device makes use of frequency bands which are not harmonised throughout the European Community (EU).
È illegale utilizzare questo radiomicrofono per qualsiasi altro scopo che non sia la trasmissione di un segnale audio ad ogni suo ricevitore o modulo sintonizzatore. Questo prodotto utilizza bande di frequenza che non sono totalmente armonizzate in tutta la Comunità Europea (EU). Dipendentemente dall’area certe aree geografica certe frequenze possono essere usate legalmente con o senza autorizzazione / licenze individuali come stabilito nella tabella delle frequenze.
Traceability Information for Europe Manufacturer: TOA Corporation 7-2-1, Minatojima-Nakamachi, Chuo-ku, Kobe, Hyogo, Japan Authorized representative: TOA Electronics Europe GmbH Suederstrasse 282, 20537 Hamburg, Germany URL: http://www.toa.
