INSTRUCTION MANUAL OUTDOOR CAMERA HOUSING C-CH200 C-CH200FH C-CH210FH C-CH210FH Thank you for purchasing TOA’s Outdoor camera housing. Please carefully follow the instructions in this manual in order to ensure long, trouble-free use of your camera housing.
TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ................................................................................ 3 2. GENERAL DESCRIPTION ............................................................................. 5 3. HANDLING PRECAUTIONS .......................................................................... 5 4. NOMENCLATURE ............................................................................................. 6 5. INSTALLATION 5.1. Installation Examples 5.1.1.
1. SAFETY PRECAUTIONS • Be sure to read the instructions in this manual section carefully before use. • Make sure to observe the instructions in this section as the conventions of safety symbols and messages regarded as very important are included. • Please keep this instruction manual handy for future reference. Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could result from mishandling.
WARNING Indicates a potentially hazardous situation which could result in death or serious personal injury if ignored or mishandled. When Installing the Camera Housing • Use nuts and bolts that are appropriate for the ceiling’s or wall’s structure and composition. Failure to do so may cause the unit to fall, resulting in personal injury. • Tighten each nut and bolt securely. Ensure that there are no loose joints after installation to prevent accidents that could result in personal injury.
CAUTION Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. When using the Camera Housing • Do not stand or sit on, nor hang down from the unit as this may cause the unit to topple over or fall down, possibly resulting in personal injury. • Keep cable wiring as far away as possible from the unit’s heater (C-CH200FH and C-CH210FH only). Also, do not insert the flammable into the unit.
4. NOMENCLATURE [Top view] Junction circuit board (inside) Sunshade [Side view] [Front view] Wiper (C-CH210FH only) Cable entry bushing (Applicable cable diameter: Ø 5 – 9.5 mm) Cable entry bushing (Applicable cable diameter: Ø10 – 17 mm) Snap fastener Used to open or close the sunshade. Note: Take care not to pinch the wiper when opening and closing the sunshade.
5. INSTALLATION The housing can be mounted on a wall by way of an optional mounting bracket or pan/tilt head. Use the housing mounting holes when mounting. Outdoor Camera Housing C-CH200 C-CH200FH C-CH210FH Outdoor Pan/Tilt Head C-PH200 Housing Fixing Stand C-BC200H Wall Mounting Bracket C-BC200K 5.1. Installation Examples 5.1.1. When using the C-BC200H Housing Fixing Stand: 5.1.2.
6. CABLE ROUTING 1. From the two cable entry bushings provided on the housing’s bottom surface, select the one that is appropriate for the diameter of cable to be used (control cable or coaxial cable). 2. Remove the selected bushing’s cap, and rubber membrane attached to prevent the entries of water and dust. 3. Run the cable through the cap to route the cable to the inside of the housing through the bushing. 4.
7. CABLE WIRING 7.1. External Control Cable and Housing Terminal Block Wiring CAUTION Sunshade • Keep wiring as far away as possible from a heater. (CCH200FH and C-CH210FH only.) Failure to do so may cause a fire or electric shock. • Do not touch a heater because fingers may be burned. (C-CH200FH and C-CH210FH only.) Junction circuit board • Be sure to use the optional CC-5941B 24 VAC adapter for the 24 VAC power supply. Using adapters other than the dedicated type could lead to a fire.
7.2. Zoom Lens Wiring Zoom lens Camera Connects to the 4-pole connector (CN8) on the junction circuit board. Zoom lens cable for internal wiring (accessory) Wiring Diagram LENS COMMON 1 2 3 4 IRIS FOCUS ZOOM 4-pole connector (female) 4-pole connector on the circuit board 7.3. Camera Wiring 7.3.1.
7.4. Coaxial Cable End Processing Process the coaxial cable end as follows: 20 3C-2V Cable 1. Strip the cable sheath 20 mm from the cable end. 2. Bend back braided copper shields over the cable sheath, then remove the insulating material 15 mm from the cable end. 5C-2V Cable 1. Strip the cable sheath 30 mm from the cable end, and braided copper shields 20 mm. 2. Remove the insulating material 15 mm from the cable end.
8. CONNECTION EXAMPLES 8.1. Connections to the CC-5011B Direct Control System Remote Controller 8.1.1. When connecting the C-CH210FH directly to the CC-5011B: CC-5941B 24 VAC Adapter 1 CAMERA 1 2 1 MAIN POWER 2 1 HOUSING POWER 2 1 CAMERA 2 2 1 CAMERA 3 2 Note Note correct polarity when connecting the dedicated AC adapter. Reversed polarity connections will cause damage to equipment.
8.1.2. When using the C-PH200 Outdoor Pan/tilt Head: CC-5941B 24 VAC Adapter 1 1 CAMERA 1 2 1 MAIN POWER 2 1 CAMERA 2 2 1 HOUSING POWER 2 Note Note correct polarity when connecting the dedicated AC adapter. Reversed polarity connections will cause damage to equipment.
8.2. Connections to the CC-5120 Relay Box 8.2.1.
8.2.2.
8.3. Connections to the C-RB100 Coaxial Multiplex Control Relay Box 8.3.1. When connecting the C-CH210FH directly to the C-RB100: When using the 100 VAC camera, connect the camera power supply directly to the 100 VAC wall outlet. (Power cannot be supplied from the C-RB100 to the 100 VAC camera.
8.3.2. When using the C-PH200 Outdoor Pan/tilt Head: • When using the 100 VAC camera, it is not connected to 1 and 2 on the C-PH200’s terminal block (upper). Connect the camera power supply directly to the 100 VAC wall outlet. (Power to the 100 VAC camera cannot be supplied from the C-RB100.
9. CAMERA AND ZOOM LENS INSTALLATION 1. Remove the camera mounting plate from the camera housing. To remove, loosen two butterfly bolts and pull them forward. 2. Mount the camera to the camera mounting plate, and the zoom lens to the zoom lens mounting plate using the supplied nuts and bolts. Note: The zoom lens mounting plate is supplied attached to the camera mounting plate. [Bolts to be used] • U1/4x10 camera mounting bolt ........................ 1 (accessory) • U1/4 plain washer .......................
10. WIPER BLADE REPLACEMENT (C-CH210FH ONLY) Because the wiper blade will wear out over years of use, replace it periodically. 1. Pull the worn wiper blade out of the holder’s notched hole. 2. Insert a new wiper blade (service part code 102-15-420-30) into the holder’s notched hole to mount it. Wiper blade Notched hole C-CH210FH Holder To mount the wiper blade, align the wiper blade slots with the holder as shown in the figure.
11. SPECIFICATIONS Model No. C-CH200 Power Source – Current Consumption - C-CH200FH C-CH210FH 24 V AC, 50/60 Hz Fan : 4.6 W Heater : 19 W Fan/heater Operating - Temperature Fan : Turns on at over Fan : 4.6 W Heater : 19 W Defroster :5W Wiper : 2.3 W Fan : Turns on at over approx. 26°C approx. 26°C Heater : Turns on at under Heater approx. 10°C : Turns on at under approx. 10°C Defroster : Turns on at under approx. 30°C Turns off at over approx.
