INSTRUCTION MANUAL WALL MOUNTING BRACKET C-BC704W TABLE OF CONTENTS 1. SAFETY PRECAUTIONS .......................... 2 2. GENERAL DESCRIPTION ........................ 4 3. HANDLING PRECAUTIONS ..................... 4 4. INSTALLATION 4.1. In-wall Wring ........................................ 5 4.2. Open Wring .......................................... 9 5. SPECIFICATIONS ................................... 12 Accessories ..............................................
1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. • We also recommend you keep this instruction manual handy for future reference.
WARNING Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury. When Installing the Unit • Avoid installing the unit at heights exceeding 16 meters above the ground since the unit could be exposed to unexpected strong winds that might cause it to fall or result in other accidents. When the Unit is in Use • Do not touch the unit during thunder and lightning, as this may result in electric shock.
2. GENERAL DESCRIPTION The C-BC704W Wall Mounting Bracket is designed to mount the C-CC704 Combination Camera to a wall. It also permits the camera to be mounted on a pole in conjunction with the optional C-BC771PM Camera Pole Mounting Bracket and YS-60B Mounting Band. 3. HANDLING PRECAUTIONS • Mount the unit to a concrete wall or robustly constructed wall surface.
4. INSTALLATION 4.1. In-wall Wiring 1. Run the composite cable supplied with the C-CC704 through the cable bushing supplied with the unit. Remove the connectors on the end of the composite cable before running the cable through the cable bushing. Insert Remove 2. Remove the rear plate from the Wall Mounting Bracket, then run the composite cable with a cable bushing mounted from the rear plate side. Rear plate 3.
4. Replace the connectors removed in Step 1 on the end of the composite cable. Note: Pay attention to the correct cable connections. Incorrect wiring at the connectors may cause damage to the connected equipment. Input connector Power supply connector Input/Output connector Terminal No.
6. Pull out the cable from the wall outlet, then connect it to the composite cable routed to the Wall Mounting Bracket. Note: Be sure to seal and insulate each connection of the cable with waterproof tape. Wall surfa ce 7. Secure the Wall Mounting Bracket to the wall surface, then waterproof the Wall Bracket's base portion which contacts the wall surface with silicone sealant material.
. Secure the C-CC704's case to the Wall Mounting Bracket with 4 hexagon socket screw, then cover these screw holes with the waterproof caps as shown in the figure below. Waterproof cap (accessory) Hexagon socket screw (accessory) C-CC704's case 9. Install the camera unit and dome cover to the case. For the procedures, refer to p. 14 of the C-CC704's instruction manual.
4.2. Open Wiring 1. Run the composite cable supplied with the C-CC704 through the cable bushing supplied with the unit. Remove the connectors on the end of the composite cable before running the cable through the cable bushing. Insert Remove 2. Remove the rubber gasket attached to the Wall Mounting Bracket, then attach it to the cable entry hole in the rear plate. Rear plate Remove Attach Rubber gasket Rubber gasket 3.
4. Secure the cable bushing to the Wall Mounting Bracket, then waterproof 2 points shown in the figure below with silicone sealant material. Sealing points 5. Replace the connectors removed in Step 1 on the end of the composite cable. Note: Pay attention to the correct cable connections. Incorrect wiring at the connectors may cause damage to the connected equipment. Input connector Power supply connector Input/Output connector Terminal No.
6. Secure the Wall Mounting Bracket to the wall surface, then waterproof the Wall Bracket's base portion which contacts the wall surface with silicone sealant material. Nut Spring washer Plain washer Anchor bolt ( M8, M10, or W3/8 ) Waterproofing area ce urfa e rfac ll su Wa ll s Wa 7. Connect the composite cable to the external wiring cable. Note: Seal and insulate each connection of the cable with waterproof tape, then house them in a waterproof plastic box.
8. Secure the C-CC704's case to the Wall Mounting Bracket with 4 hexagon socket screw, then cover these screw holes with the waterproof caps as shown in the figure below. Waterproof cap (accessory) Hexagon socket screw (accessory) C-CC704's case 9. Install the camera unit and dome cover to the case. For the procedures, refer to p. 14 of the C-CC704's instruction manual. 5.
